Formation of nanostructured surface layer on AISI 304 stainless steel by means of surface mechanical attrition treatment

A nanostructured surface layer was formed on an AISI 304 stainless steel with low stacking-fault energy by means of the surface mechanical attrition treatment (SMAT). The microstructure of the surface layer of the SMATed sample was characterized by using X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM), and cross-sectional TEM observation was performed to reveal the deformation-driven grain refinement mechanism for the f.c.c. materials with very low stacking-fault energy during SMAT. The grain refinement process in the surface layer involves formation of planar dislocation arrays and twins in deformed grains, twin-twin intersections leading to grain subdivision and a martensite transformation as well, and formation of randomly orientated refined crystallites. The formation of nanocrystallites in the top surface layer was ascribed to the much large strain and strain rate, as well as the multidirectional repetitive loading. (C) 2003 Acta Materialia Inc. Published by Elsevier Science Ltd. All rights reserved.

[1]  S. Suresh,et al.  Nanocrystallization During Nanoindentation of a Bulk Amorphous Metal Alloy at Room Temperature , 2002, Science.

[2]  Jens Lothe John Price Hirth,et al.  Theory of Dislocations , 1968 .

[3]  G. Chin,et al.  Twin-slip, twin-twin and slip-twin interactions in Co-8 wt.% Fe alloy single crystals , 1973 .

[4]  L. Murr.  Interfacial phenomena in metals and alloys , 1975 .

[5]  Jian Lu,et al.  Surface nanocrystallization of iron induced by ultrasonic shot peening , 1999 .

[6]  L. Murr,et al.  Comparison of residual microstructures for 304 stainless steel shock loaded in plane and cylindrical geometries: Implications for dynamic compaction and forming , 1985 .

[7]  S. Takaki,et al.  Atomic-Level Observation of Disclination Dipoles in Mechanically Milled, Nanocrystalline Fe , 2002, Science.

[8]  Gang Liu,et al.  Low carbon steel with nanostructured surface layer induced by high-energy shot peening , 2001 .

[9]  Jian Lu,et al.  Surface nanocrystallization of 316L stainless steel induced by ultrasonic shot peening , 2000 .

[10]  J. Ding,et al.  Microstructural evolution of 304 stainless steel during mechanical milling , 1996 .

[11]  N. Hansen,et al.  New discoveries in deformed metals , 2001 .

[12]  L. Alexander,et al.  X-Ray diffraction procedures for polycrystalline and amorphous materials , 1974 .

[13]  G. Thomas,et al.  The martensite phases in 304 stainless steel , 1970 .

[14]  W. Johnson,et al.  Structural and thermodynamic properties of heavily mechanically deformed Ru and AlRu , 1989 .

[15]  L. Rémy.  Kinetics of f.c.c. deformation twinning and its relationship to stress-strain behaviour , 1978 .

[16]  Siegfried S. Hecker,et al.  Effects of Strain State and Strain Rate on Deformation-Induced Transformation in 304 Stainless Steel: Part I. Magnetic Measurements and Mechanical Behavior , 1982 .

[17]  D. Kuhlmann-wilsdorf,et al.  Overview no. 96: Evolution of F.C.C. deformation structures in polyslip , 1992 .

[18]  R. Armstrong.  Wedge Dislocation as the Elastic Counterpart of a Crystal Deformation Twin , 1968, Science.

[19]  G. B. Olson,et al.  A MECHANISM FOR THE STRAIN-INDUCED NUCLEATION OF MARTENSITIC TRANSFORMATIONS* , 1972 .

[20]  W. W. Milligan,et al.  Observation and measurement of grain rotation and plastic strain in nanostructured metal thin films , 1995 .

[21]  R. Reed,et al.  The spontaneous martensitic transformations in 18% Cr, 8% Ni steels , 1962 .

[22]  R. Lagneborgj.  The martensite transformation in 18% Cr-8% Ni steels , 1964 .

[23]  R. Scattergood,et al.  Studies of deformation mechanisms in ultra-fine-grained and nanostructured Zn , 2002 .

[24]  L. Murr,et al.  Effects of Strain State and Strain Rate on Deformation-Induced Transformation in 304 Stainless Steel: Part II. Microstructural Study , 1982 .

[25]  L. Murr,et al.  Deformation-induced martensitic characteristics in 304 and 316 stainless steels during room-temperature rolling , 1995 .

[26]  G. Chin,et al.  The interaction of twins with existing substructure and twins in cobalt-iron alloys , 1974 .

[27]  R. Penelle,et al.  Development of texture and microstructure during cold-rolling and annealing of F.C.C. alloys: Example of an austenitic stainless steel , 1989 .

[28]  S. Kalidindi,et al.  Strain hardening regimes and microstructural evolution during large strain compression of low stacking fault energy fcc alloys that form deformation twins , 1997 .

[29]  J. A. Venables,et al.  The martensite transformation in stainless steel , 1962 .

[30]  A. Paxton.  TWINNING IN ADVANCED MATERIALS , 1994 .

[31]  S. Poon,et al.  Deformation-induced nanocrystal formation in shear bands of amorphous alloys , 1994, Nature.

[32]  Jian Lu,et al.  An investigation of surface nanocrystallization mechanism in Fe induced by surface mechanical attrition treatment , 2002 .

[33]  Xiaolei Wu,et al.  Microstructure and evolution of mechanically-induced ultrafine grain in surface layer of AL-alloy subjected to USSP , 2002 .