Assessment of debonding in sandwich CF/EP composite beams using A0 Lamb wave at low frequency

The aim of this study is to quantitatively assess debonding in sandwich CF/EP composite structures with a honeycomb core using acoustic waves activated and captured by surface-mounted PZT elements. For experimental investigation, debonding was introduced at different locations in sandwich CF/EP composite beams. The fundamental anti-symmetric A0 Lamb mode was excited at a low frequency. The transmitted and reflected wave signals in both surface panels were captured by PZT elements after interacting with the debonding damage and specimen boundaries. Aided by finite element analysis (FEA), the differences in wave propagation characteristics in sandwich composite beams and composite laminate (e.g. skin panel only) were investigated. The debonding location was assessed using the time-of-flight (ToF) of damage-reflected waves, and the severity of debonding was evaluated using both the magnitude of the reflected wave signal and the delay in the ToF of Lamb wave signals. Good correlation between the experimental and FEA simulation results was observed. The results demonstrate the effectiveness of Lamb waves activated and captured by surface-mounted PZT elements on either surface of sandwich composite structures in assessing debonding.

[1]  A. Raghavan,et al.  Guided-wave signal processing using chirplet matching pursuits and mode correlation for structural health monitoring , 2007 .

[2]  Constantinos Soutis,et al.  Piezoelectric transducer arrangement for the inspection of large composite structures , 2007 .

[3]  Zhongqing Su,et al.  A quantitative identification approach for delamination in laminated composite beams using digital damage fingerprints (DDFs) , 2006 .

[4]  Constantinos Soutis,et al.  Lamb waves for the non-destructive inspection of monolithic and sandwich composite beams , 2005 .

[5]  J. Rose.  Ultrasonic Waves in Solid Media , 1999 .

[6]  Yiu-Wing Mai,et al.  Delamination detection in smart composite beams using Lamb waves , 2004 .

[7]  Constantinos Soutis,et al.  Non-destructive inspection of sandwich and repaired composite laminated structures , 2005 .

[8]  B. Gangadhara Prusty,et al.  Prediction of flange debonding in composite stiffened panels using an analytical crack tip element-based methodology , 2008 .

[9]  Costas Soutis,et al.  Real-time nondestructive evaluation of fiber composite laminates using low-frequency Lamb waves. , 2002, The Journal of the Acoustical Society of America.

[10]  Zhongqing Su,et al.  A built-in active sensor network for health monitoring of composite structures , 2006 .

[11]  Dong Wang,et al.  Probability of the presence of damage estimated from an active sensor network in a composite panel of multiple stiffeners , 2009 .

[12]  L. Edwards,et al.  Residual stresses in structures reinforced with adhesively bonded straps designed to retard fatigue crack growth , 2008 .

[13]  Michelle S. Hoo Fatt,et al.  Dynamic models for low-velocity impact damage of composite sandwich panels – Part A: Deformation , 2001 .

[14]  Suszanne Thwaites,et al.  NON-DESTRUCTIVE TESTING OF HONEYCOMB SANDWICH STRUCTURES USING ELASTIC WAVES , 1995 .

[15]  Constantinos Soutis,et al.  Detection of Low-velocity Impact Damage in Composite Plates using Lamb Waves , 2004 .

[16]  Carlos E. S. Cesnik,et al.  Review of guided-wave structural health monitoring , 2007 .

[17]  Guoliang Huang,et al.  Guided wave propagation in honeycomb sandwich structures using a piezoelectric actuator/sensor system , 2009 .

[18]  F. Yuan,et al.  Diagnostic Lamb waves in an integrated piezoelectric sensor/actuator plate: analytical and experimental studies , 2001 .

[19]  Zhongqing Su,et al.  Quantitative identification of multiple damage in laminated composite beams using A 0 Lamb mode , 2011 .

[20]  Lin Ye,et al.  Guided Lamb waves for identification of damage in composite structures: A review , 2006 .