Thermal Spray Coatings Engineered from Nanostructured Ceramic Agglomerated Powders for Structural, Thermal Barrier and Biomedical Applications: A Review

Thermal spray coatings produced from nanostructured ceramic agglomerated powders were tailored for different applications, some of which required almost completely opposite performance characteristics (e.g., anti-wear and abradable coatings). The influence of nanostructured materials on important areas, such as, thermal barrier coatings (TBCs) and biomedical coatings was also investigated. It was determined that by controlling the distribution and character of the semi-molten nanostructured agglomerated particles (i.e., nanozones) embedded in the coating microstructure, it was possible to engineer coatings that exhibited high toughness for anti-wear applications or highly friable for use as abradables, exhibiting abradability levels equivalent to those of metallic-based abradables. It is shown that nanozones, in addition to being very important for the mechanical behavior, may also play a key role in enhancing and controlling the bioactivity levels of biomedical coatings via biomimetism. This research demonstrates that these nanostructured coatings can be engineered to exhibit different properties and microstructures by spraying nanostructured ceramic agglomerated powders via air plasma spray (APS) or high velocity oxy-fuel (HVOF). Finally, in order to present readers with a broader view of the current achievements and future prospects in this area of research, a general overview is presented based on the main papers published on this subject in the scientific literature.

[1]  E. Jordan,et al.  Fabrication and evaluation of plasma sprayed nanostructured alumina-titania coatings with superior properties , 2001 .

[2]  B. Marple,et al.  Development of osteoblast colonies on new bioactive coatings , 2006, International Thermal Spray Conference.

[3]  T. Webster,et al.  Enhanced functions of osteoblasts on nanophase ceramics. , 2000, Biomaterials.

[4]  Sanjay Sampath,et al.  On the role of particle state and deposition procedure on mechanical, tribological and dielectric response of high velocity oxy-fuel sprayed alumina coatings , 2006 .

[5]  D. Sun,et al.  Microstructural feature, thermal shock resistance and isothermal oxidation resistance of nanostructured zirconia coating , 2006 .

[6]  H. Erickson,et al.  Fibronectin molecule visualized in electron microscopy: a long, thin, flexible strand , 1981, The Journal of cell biology.

[7]  K. Khor,et al.  Effect of Heat Treatment on High Pressure Plasma Sprayed Hydroxyapatite Coatings , 2002 .

[8]  F. Monteiro,et al.  Glass-reinforced hydroxyapatite composites: fracture toughness and hardness dependence on microstructural characteristics. , 1999, Biomaterials.

[9]  H. Liao,et al.  Phase composition and stability of nanostructured 4.7 wt.% yttria-stabilized zirconia coatings deposited by atmospheric plasma spraying , 2006 .

[10]  C. Ding,et al.  Thermal shock resistances of nanostructured and conventional zirconia coatings deposited by atmospheric plasma spraying , 2005 .

[11]  E. Jordan,et al.  Microstructure development of Al2O3-13wt.%TiO2 plasma sprayed coatings derived from nanocrystalline powders , 2002 .

[12]  Hua Li,et al.  HVOF spraying of nanostructured hydroxyapatite for biomedical applications , 2005 .

[13]  C. Berndt,et al.  Integrity of nanostructured partially stabilized zirconia after plasma spray processing , 2001 .

[14]  Yi Zeng,et al.  Atmospheric plasma sprayed coatings of nanostructured zirconia , 2002 .

[15]  O. Reikerås,et al.  Failure of HA coating on a gritblasted acetabular cup: 155 patients followed for 7-10 years , 2002, Acta orthopaedica Scandinavica.

[16]  S. Lee,et al.  Influence of feedstock and spraying parameters on the depositing efficiency and microhardness of plasma-sprayed zirconia coatings , 2004 .

[17]  E. Chang,et al.  The bonding of plasma-sprayed hydroxyapatite coatings to titanium: effect of processing, porosity and residual stress , 2003 .

[18]  S. Bhaduri,et al.  Identification of t' Phase in ZrO2-7.5 wt% Y2O3 Thermal-Barrier Coatings , 1988 .

[19]  H. Liao,et al.  Nanostructured zirconia–30 vol.% alumina composite coatings deposited by atmospheric plasma spraying , 2005 .

[20]  Nack J. Kim,et al.  Microstructure and wear resistance of nanostructured Al2O3-8wt.%TiO2 coatings plasma-sprayed with nanopowders , 2006 .

[21]  C. Ding,et al.  Tribological properties of nanostructured zirconia coatings deposited by plasma spraying , 2002 .

[22]  C. Berndt,et al.  Bimodal distribution of mechanical properties on plasma sprayed nanostructured partially stabilized zirconia , 2002 .

[23]  P. Ctibor,et al.  Structure and mechanical properties of plasma sprayed coatings of titania and alumina , 2006 .

[24]  Hua Li,et al.  Characteristics of the nanostructures in thermal sprayed hydroxyapatite coatings and their influence on coating properties , 2006 .

[25]  C. Ding,et al.  Phase composition of nanostructured zirconia coatings deposited by air plasma spraying , 2005 .

[26]  J. Mostaghimi,et al.  Thermomechanical behavior of nanostructured plasma sprayed zirconia coatings , 2006, International Thermal Spray Conference.

[27]  Bi Zhang,et al.  Grinding of nanostructured ceramic coatings: surface observations and material removal mechanisms , 2002 .

[28]  B. Espehaug,et al.  The performance of two hydroxyapatite-coated acetabular cups compared with Charnley cups. From the Norwegian Arthroplasty Register. , 2002, The Journal of bone and joint surgery. British volume.

[29]  Hua Li,et al.  Effect of the powders’ melting state on the properties of HVOF sprayed hydroxyapatite coatings , 2000 .

[30]  Christian Moreau,et al.  HVOF-Sprayed Coatings Engineered from Mixtures of Nanostructured and Submicron Al2O3-TiO2 Powders: An Enhanced Wear Performance , 2007 .

[31]  S. Iijima.  Helical microtubules of graphitic carbon , 1991, Nature.

[32]  Sunghak Lee,et al.  Correlation of microstructure and wear resistance of Al2O3-TiO2 coatings plasma sprayed with nanopowders , 2006 .

[33]  B. Marple,et al.  From APS to HVOF spraying of conventional and nanostructured titania feedstock powders: a study on the enhancement of the mechanical properties , 2006 .

[34]  Christopher C. Berndt,et al.  Fatigue and mechanical properties of nanostructured and conventional titania (TiO2) thermal spray coatings , 2007 .

[35]  Yi Zeng,et al.  Microstructural characterization of plasma-sprayed nanostructured zirconia powders and coatings , 2003 .

[36]  S. Gong,et al.  Heat treatment of nanostructured thermal barrier coating , 2007 .

[37]  L. Shaw,et al.  Indentation fracture behavior of plasma-sprayed nanostructured Al2O3-13wt.%TiO2 coatings , 2003 .

[38]  N. Padture,et al.  Improved interfacial mechanical properties of Al2O3-13wt%TiO2 plasma-sprayed coatings derived from nanocrystalline powders , 2003 .

[39]  S. Lee,et al.  Wear of plasma-sprayed nanostructured zirconia coatings against stainless steel under distilled-water conditions , 2003 .

[40]  Christian Coddet,et al.  Improvement in wear resistance of plasma sprayed yttria stabilized zirconia coating using nanostructured powder , 2004 .

[41]  B. Marple,et al.  Enhanced ductility in thermally sprayed titania coating synthesized using a nanostructured feedstock , 2005 .

[42]  B. Marple,et al.  Optimized HVOF titania coatings , 2003 .

[43]  Brian R. Lawn,et al.  A Critical Evaluation of Indentation Techniques for Measuring Fracture Toughness: I , 1981 .

[44]  A. R. Nicoll,et al.  The wear mechanisms occurring in abradable seals of gas turbines , 1989 .

[45]  T. Webster,et al.  Specific proteins mediate enhanced osteoblast adhesion on nanophase ceramics. , 2000, Journal of biomedical materials research.

[46]  Bi Zhang,et al.  Grinding of nanostructural ceramic coatings: damage evaluation , 2003 .

[47]  Tommi Varis,et al.  Parameter optimization of HVOF sprayed nanostructured alumina and alumina-nickel composite coatings , 2006 .

[48]  Yi Zeng,et al.  Microstructure of alumina–3wt.% titania coatings by plasma spraying with nanostructured powders , 2003 .

[49]  Soo‐Wohn Lee,et al.  Phase composition and microstructure of vacuum plasma sprayed nanostructured zirconia coating , 2003 .

[50]  C. Koch,et al.  Nanostructured Materials: Processing, Properties and Applications , 2006 .

[51]  H. Herman,et al.  Studies of the microstructure and properties of dense ceramic coatings produced by high-velocity oxygen-fuel combustion spraying , 2004 .

[52]  J. Blacha.  High osteolysis and revision rate with the hydroxyapatite-coated ABG hip prostheses65 hips in 56 young patients followed for 5–9 years , 2004, Acta orthopaedica Scandinavica.

[53]  R. McPherson,et al.  A review of microstructure and properties of plasma sprayed ceramic coatings , 1989 .

[54]  H. Liao,et al.  Wear characteristics of plasma-sprayed nanostructured yttria partially stabilized zirconia coatings , 2004, Thermal Spray 2004: Proceedings from the International Thermal Spray Conference.

[55]  C. Coddet,et al.  Microstructure of plasma-sprayed titania coatings deposited from spray-dried powder , 2003 .

[56]  T. Webster,et al.  Increased viable osteoblast density in the presence of nanophase compared to conventional alumina and titania particles. , 2004, Biomaterials.

[57]  Soo‐Wohn Lee,et al.  Plasma spray coatings in different nanosize alumina , 2002 .

[58]  P. Chu,et al.  In vitro bioactivity of plasma-sprayed TiO2 coating after sodium hydroxide treatment , 2006 .

[59]  B. Marple,et al.  Superior performance of high-velocity oxyfuel-sprayed nanostructured TiO2 in comparison to air plasma-sprayed conventional Al2O3-13TiO2 , 2005 .

[60]  C. Berndt,et al.  Evaluation of microhardness and elastic modulus of thermally sprayed nanostructured zirconia coatings , 2001 .

[61]  Soo‐Wohn Lee,et al.  Evaluation of unlubricated wear properties of plasma-sprayed nanostructured and conventional zirconia coatings by SRV tester , 2006 .

[62]  C. Ding,et al.  Nanostructured zirconia coating prepared by atmospheric plasma spraying , 2002 .

[63]  F. Ghasripoor,et al.  Abradables improve gas turbine efficiency , 1997 .

[64]  B. Marple,et al.  High weibull modulus HVOF titania coatings , 2003 .

[65]  T. Fischer,et al.  Comparison of HVOF and plasma-sprayed alumina/titania coatings—microstructure, mechanical properties and abrasion behavior , 2003 .

[66]  C. Bünger,et al.  Role of different loading conditions on resorption of hydroxyapatite coating evaluated by histomorphometric and stereological methods , 1996, Journal of orthopaedic research : official publication of the Orthopaedic Research Society.

[67]  B. Lawn,et al.  A Critical Evaluation of Indentation Techniques for Measuring Fracture Toughness: II, Strength Method , 1981 .

[68]  P. Chu,et al.  Plasma-treated nanostructured TiO(2) surface supporting biomimetic growth of apatite. , 2005, Biomaterials.

[69]  Leon L. Shaw,et al.  Development and implementation of plasma sprayed nanostructured ceramic coatings , 2001 .

[70]  C. Berndt,et al.  Nanostructured and conventional YSZ coatings deposited using APS and TTPR techniques , 2006 .

[71]  L. Shaw,et al.  The dependency of microstructure and properties of nanostructured coatings on plasma spray conditions , 2000 .

[72]  Xianfan Xu,et al.  Thermophysical properties of thermal barrier coatings , 1999 .

[73]  Chyun-Yu Yang,et al.  Failure of hydroxyapatite-coated acetabular cups. Ten-year follow-up of 85 Landos Atoll arthroplasties. , 2002, The Journal of bone and joint surgery. British volume.

[74]  C. Ding,et al.  Investigation of the thermomechanical properties of a plasma-sprayed nanostructured zirconia coating , 2003 .

[75]  Yi Zeng,et al.  Characterization of alumina–3 wt.% titania coating prepared by plasma spraying of nanostructured powders , 2004 .

[76]  B. Marple,et al.  Biomimetic Ceramic Surfaces Produced by Thermal Spraying Nanostructured Titania: A Coating Alternative to Hydroxyapatite on Orthopedic Implants? , 2006 .

[77]  P. Liaw,et al.  The mechanical properties of nanostructured materials , 2001 .

[78]  Peter R. Strutt,et al.  Abrasive wear characteristics of plasma sprayed nanostructured alumina/titania coatings , 2000 .

[79]  N. Gane,et al.  Structural characterization of plasma-sprayed hydroxylapatite coatings , 1995 .

[80]  T. Webster,et al.  Osteoblast adhesion on nanophase ceramics. , 1999, Biomaterials.