Design, Optimization, and Fabrication of Slotted-Interdigitated Thin Metallic Bipolar Plates for PEM Fuel Cells

Thin metallic sheet bipolar plates (BPPs) with sustainable coating are promising candidates to replace conventional graphitic or machined thick metal plates due to their lightweight and low cost. Interdigitated flow field design is easier for two stamped thin metallic sheets joined together to compose reactant flow fields in both sides and serpentine coolant flow field in the middle. Unfortunately, this kind of BPP inevitable brings two main defects: rupture of material during forming process and uneven flow distribution in practical operation. First, we propose a slotted-interdigitated configuration of the flow field for proton exchange membrane fuel cell with consideration of the characteristics of the metallic sheet forming process. In order to relieve the uneven flow distribution, an analytic model is introduced to analyze the reactant gas flow based on the similarity between the gas flow and the electrical current. Furthermore, an optimization model is proposed. The depth of the slot on the channel rib is optimized to eliminate the uneven flow distribution to obtain high reaction performance. Second, we studied the BPPs from the manufacturability perspective because it is also another important factor that should be considered in the design stage. The key geometric dimensions of flow field section, where the rupture occurs, are extracted and parametrized. Finite element analysis model is established to analyze the formability of BPP by flexible forming process (FFP). In addition, different dies with various flow channel sections are prepared and experiments are performed. Some design principles about material selection and key geometric dimension definition are proposed to improve the formability of BPPs. In the end, based on the design principles and experimental results, the dies are carefully design and fabricated experimental setup for FFP is prepared and practical experiments are performed. High quality metallic BPPs are achieved eventually by FFP. DOI: 10.1115/1.4002229

[1]  D. Guinea,et al.  Electric modelling and image analysis of channel flow in bipolar plates , 2007 .

[2]  J. Whitelaw,et al.  Convective heat and mass transfer , 1966 .

[3]  Ramana G. Reddy,et al.  Effect of channel dimensions and shape in the flow-field distributor on the performance of polymer electrolyte membrane fuel cells , 2003 .

[4]  Yao Shen,et al.  An investigation into nickel implanted 316L stainless steel as a bipolar plate for PEM fuel cell , 2008 .

[5]  W. Kout,et al.  Bipolar plates for PEM fuel cells , 2003 .

[6]  Jun Ni,et al.  Fabrication of Metallic Bipolar Plates for Proton Exchange Membrane Fuel Cell by Flexible Forming Process-Numerical Simulations and Experiments , 2010 .

[7]  Hu Shi-xin.  Numerical simulation of flow field at the anode of proton exchange membrane fuel cell(PEMFC) and optimization of channel dimensions in the flow-field plate , 2005 .

[8]  Jun Ni,et al.  Flow channel shape optimum design for hydroformed metal bipolar plate in PEM fuel cell , 2008 .

[9]  Peng Hu,et al.  Analysis and optimization of flow distribution in parallel-channel configurations for proton exchange membrane fuel cells , 2009 .

[10]  M. Husnu Dirikolu,et al.  Computer aided modelling of flexible forming process , 2004 .

[11]  Pradip Majumdar,et al.  Development of bipolar plates with different flow channel configurations for fuel cells , 2009 .

[12]  J. Ni,et al.  Investigation of micro/meso sheet soft punch stamping process - simulation and experiments , 2009 .

[13]  Sreenivas Jayanti,et al.  Flow distribution and pressure drop in parallel-channel configurations of planar fuel cells , 2005 .

[14]  David J. Browne,et al.  Optimisation of aluminium sheet forming using a flexible die , 1995 .

[15]  Xianguo Li,et al.  Review of bipolar plates in PEM fuel cells: Flow-field designs , 2005 .

[16]  Muammer Koç,et al.  Fabrication of micro-channel arrays on thin metallic sheet using internal fluid pressure: Investigations on size effects and development of design guidelines , 2008 .

[17]  Isa Bar-On,et al.  Technical cost analysis for PEM fuel cells , 2002 .

[18]  Allen M. Hermann,et al.  Bipolar plates for PEM fuel cells: A review , 2005 .

[19]  Muammer Koç,et al.  Feasibility investigations on a novel micro-manufacturing process for fabrication of fuel cell bipolar plates: Internal pressure-assisted embossing of micro-channels with in-die mechanical bonding , 2007 .

[20]  Peng Hu,et al.  Optimization design of slotted-interdigitated channel for stamped thin metal bipolar plate in proton exchange membrane fuel cell , 2009 .