Evidence of speckle in extreme-UV lithography.

Based on reflective optics at 13.5 nm, extreme-UV lithography is the ultimate top-down technique to define structures below 22 nm but faces several challenges arising from the discrete nature of light and matter. Owing to the short wavelength, mask surface roughness plays a fundamental role in the increase of speckle pattern contrast, compromising the uniformity of the printed features. Herein, we have used a mask with engineered gradient surface roughness to illustrate the impact that speckle has on the resulting photoresist pattern. The speckle increases the photoresist roughness, but surprisingly, only when the mask surface roughness is well above existing manufacturing capabilities.

[1]  Angeliki Tserepi,et al.  Quantification of line-edge roughness of photoresists. II. Scaling and fractal analysis and the best roughness descriptors , 2003 .

[2]  Kenneth A. Goldberg,et al.  The SEMATECH Berkeley microfield exposure tool: learning at the 22-nm node and beyond , 2009, Advanced Lithography.

[3]  W. Dehaene,et al.  Induced Variability of Cell-to-Cell Interference by Line Edge Roughness in nand Flash Arrays , 2012, IEEE Electron Device Letters.

[4]  Bruno M. La Fontaine,et al.  Characterization of line-edge roughness in photoresist using an image fading technique , 2004, SPIE Advanced Lithography.

[5]  C. Wagner,et al.  EUV lithography: Lithography gets extreme , 2010 .

[6]  Evangelos Gogolides,et al.  Photoresist line-edge roughness analysis using scaling concepts , 2004 .

[7]  Kenneth A. Goldberg,et al.  Replicated mask surface roughness effects on EUV lithographic patterning and line edge roughness , 2011, Advanced Lithography.

[8]  Akira Takada,et al.  Novel low thermal expansion material for EUV application , 2006, SPIE Advanced Lithography.

[9]  Jan Baselmans,et al.  Speckle in optical lithography and the influence on line width roughness , 2009, Advanced Lithography.

[10]  G. Gallatin,et al.  Residual speckle in a lithographic illumination system , 2009 .

[11]  David Z. Pan,et al.  Electrical impact of line-edge roughness on sub-45-nm node standard cells , 2010 .

[12]  O. Noordman,et al.  Speckle in optical lithography and its influence on linewidth roughness , 2009 .

[13]  James W. Thackeray,et al.  Stochastic exposure kinetics of EUV photoresists: a simulation study , 2011, Advanced Lithography.

[14]  Guojing Zhang,et al.  System-level line-edge roughness limits in extreme ultraviolet lithography , 2008 .

[15]  Yan Du,et al.  EUV mask process development and integration , 2006, Photomask Japan.

[16]  Patrick P. Naulleau,et al.  Modeling the transfer of line edge roughness from an EUV mask to the wafer , 2011, Advanced Lithography.

[17]  Patrick P. Naulleau,et al.  Do not always blame the photons: Relationships between deprotection blur, line-edge roughness, and shot noise in extreme ultraviolet photoresists , 2009 .

[18]  C. Mack,et al.  Stochastic exposure kinetics of extreme ultraviolet photoresists: simulation study , 2011 .

[20]  Roel Gronheid,et al.  Resist roughness evaluation and frequency analysis: metrological challenges and potential solutions for extreme ultraviolet lithography , 2010 .

[21]  D. Remiens,et al.  Study of Ni2–Mn–Ga phase formation by magnetron sputtering film deposition at low temperature onto Si substrates and LaNiO3∕Pb(Ti,Zr)O3 buffer , 2010 .

[22]  Kenneth A. Goldberg,et al.  Extreme ultraviolet mask substrate surface roughness effects on lithographic patterning , 2010 .

[23]  Gregg M Gallatin,et al.  Line-edge roughness transfer function and its application to determining mask effects in EUV resist characterization. , 2003, Applied optics.