Analysis of the spreader track wheels premature damages

Abstract The superstructure of the ARs 2000 spreader leans on three crawlers of identical length, width and height. Serious damage to the track wheels threads occurred already during the spreader’s travel from the erection site to the open pit mine as well as immediately after the overburden system exploitation started. The goal of the study presented in this paper was to diagnose the cause of the track wheels premature damage. Contact stresses on the track wheel bearing surface are defined by applying Hertz’s theory and FEM. In order to clarify the causes of the damages, experimental investigations were performed with the purpose of defining the chemical composition, tensile properties, impact toughness and macro and microhardness of the track wheel material. Metallographic examinations were also conducted. Based on the results of the analytical–numerical–experimental analysis, it can be concluded that track wheels failures are predominantly caused by the ‘design-in’ and ‘manufacturing-in’ defects.

[1]  Borut Kosec,et al.  Fatigue cracking of an aircraft wheel , 2002 .

[2]  Uwe Zerbst,et al.  Failure and damage tolerance aspects of railway components , 2011 .

[3]  M. A. Hadianfard,et al.  Structural Failure of a Telescopic Shiploader during Installation , 2007 .

[4]  C. J. Tyne,et al.  Correlation of Yield Strength and Tensile Strength with Hardness for Steels , 2008, Journal of Materials Engineering and Performance.

[5]  H. Sehitoglu,et al.  Strengthening Hadfield steel welds by nitrogen alloying , 2009 .

[6]  Ken Gall,et al.  Analysis of the fatigue failure of a mountain bike front shock , 2004 .

[7]  Nader G. Zamani.  CATIA V5 FEA Tutorials Release 16 , 2005 .

[8]  Colin Gagg,et al.  Wear as a product failure mechanism – Overview and case studies , 2007 .

[9]  Donald A. Shockey,et al.  Analysis of failed aircraft wheel assembly , 2006 .

[10]  Miodrag Arsić,et al.  Bucket wheel excavator: Integrity assessment of the bucket wheel boom tie-rod welded joint , 2011 .

[11]  Colin Gagg,et al.  Failure of components and products by ‘engineered-in’ defects: Case studies , 2005 .

[12]  S. Timoshenko,et al.  Theory of elasticity , 1975 .

[13]  C.R.F. Azevedo,et al.  Failure analysis of a cast steel railway wheel , 2004 .

[14]  B. Karlsson,et al.  Microstructural evaluation and interpretation of the mechanically and thermally affected zone under railway wheel flats , 1999 .

[15]  Zoran D. Petković,et al.  Failure analysis and redesign of the bucket wheel excavator two-wheel bogie , 2010 .

[16]  Colin Gagg.  Domestic product failures: Case studies , 2005 .

[17]  Nenad Zrnić,et al.  Failure analysis of the end eye connection of the bucket wheel excavator portal tie-rod support , 2009 .

[18]  Soumitra Tarafder,et al.  Failure analysis of railroad wheels , 2009 .

[19]  E Hippert,et al.  Fracture of an aircraft's landing gear , 2002 .

[20]  Jerzy Czmochowski,et al.  Half-shaft undercarriage systems – designing and operating problems , 2009 .

[21]  Dipankar Chakravorty,et al.  Failure Analysis of Stacker-cum-Reclaimer in Ore Handling Plant , 2008 .

[22]  Richard Clegg.  Failure of planetary pinions in earth moving equipment—a failure analysis approach , 2000 .

[23]  Zhi-wei Yu,et al.  Failure investigation on the cracked crawler pad link , 2010 .

[24]  Jerzy Czmochowski,et al.  Application of Thiessen polygons in control volume model of solidification , 2007 .

[25]  Jerzy Czmochowski,et al.  An analysis of the causes of a BWE counterweight boom support fracture , 2010 .

[26]  R. J. Pargeter,et al.  Technical failure investigation of welded structures (or how to get the most out of failures) , 2005 .

[27]  Sankaran Mahadevan,et al.  Fatigue crack initiation life prediction of railroad wheels , 2006 .