3D CFD/FEM analysis of thermomechanical long-term behaviour in SOFCs: Furnace operation with different fuel gases

Abstract Full commercialisation of the solid oxide fuel cell (SOFC) technology is limited by technological challenges, in particular due to the thermomechanical reliability of the components. The long-term thermomechanical behaviour is especially affected by the operation environment. Most of the research and development studies, as well as laboratory studies are performed within furnaces rather than operating in a real system environment. However, the thermomechanical response of fuel cells operating in the furnace, especially operating with different fuel gas compositions is not fully understood, yet. The present study investigates the thermomechanical comparison of H 2 , 77% CH 4 and 38% CH 4 operation. A three dimensional coupled CFD/FEM sub-model, derived from a whole stack model and experimentally determined data is used. The analyses account both for the thermo fluid flow and the nonlinear elastoplastic, creep strain material behaviour. The thermomechanical behavior of the most favourable operation condition has been analysed for 1200 h operation time. The results are validated qualitatively and quantitatively using post-mortem images and creep strain data, respectively.

[1]  Jürgen Garche,et al.  Encyclopedia of electrochemical power sources , 2009 .

[2]  Lieh-Kwang Chiang,et al.  Thermal stress analysis of a planar SOFC stack , 2007 .

[3]  Scott E. Grasman,et al.  Strategies for stationary and portable fuel cell markets , 2011 .

[4]  Murat Peksen,et al.  3D transient multiphysics modelling of a complete high temperature fuel cell system using coupled CFD and FEM , 2014 .

[5]  Murat Peksen,et al.  3D thermomechanical behaviour of solid oxide fuel cells operating in different environments , 2013 .

[6]  Murat Peksen,et al.  3D coupled CFD/FEM modelling and experimental validation of a planar type air pre-heater used in SOF , 2011 .

[7]  Murat Peksen,et al.  A coupled 3D thermofluid–thermomechanical analysis of a planar type production scale SOFC stack , 2011 .

[8]  Tak-Hyoung Lim,et al.  Operating characteristics of a 5 kW class anode-supported planar SOFC stack for a fuel cell/gas turbine hybrid system , 2008 .

[9]  Murat Peksen,et al.  3D transient thermomechanical behaviour of a full scale SOFC short stack , 2013 .

[10]  H. Yakabe,et al.  Evaluation of the residual stress for anode-supported SOFCs , 2004 .

[11]  Rolf W. Steinbrech,et al.  Advanced measurement techniques to characterize thermo-mechanical aspects of solid oxide fuel cells , 2007 .

[12]  Tsung Leo Jiang,et al.  Thermal-stress analyses of an operating planar solid oxide fuel cell with the bonded compliant seal design , 2009 .

[13]  Detlef Stolten,et al.  Fuel Cell Science and Engineering, Materials, Processes, Systems and Technology , 2012 .

[14]  L. Blum,et al.  FUEL CELLS – SOLID OXIDE FUEL CELLS | Systems , 2009 .

[15]  J. E. Dorn,et al.  EXPERIMENTAL CORRELATIONS FOR HIGH-TEMPERATURE CREEP. , 1968 .

[16]  Chih-Kuang Lin,et al.  High-temperature tensile and creep properties of a ferritic stainless steel for interconnect in solid oxide fuel cell , 2011 .

[17]  Murat Peksen,et al.  Hierarchical 3D multiphysics modelling in the design and optimisation of SOFC system components , 2011 .

[18]  Wolfgang Winkler,et al.  Design studies of mobile applications with SOFC-heat engine modules , 2002 .

[19]  Miriam Kemm,et al.  Steady state and transient thermal stress analysis in planar solid oxide fuel cells , 2005 .