A Solid-State Intrinsically Stretchable Polymer Solar Cell.

An organic solar cell based on a bulk heterojunction of a conjugated polymer and a methanofullerene PC61BM or PC71BM exhibits a complex morphology that controls both its photovoltaic and mechanical compliance (flexibility and stretchability). Here, the donor-acceptor blend of poly(thieno[3,4-b]-thiophene/benzodithiophene) (PTB7) and PC71BM containing a small amount of diiodooctane (DIO) in the spin-casting solution is reported to exhibit elastic deformability. The blend comprises nanometer-size, nanocrystalline grains that are relatively uniformly distributed. Large external deformation is accommodated by relative sliding between the grains. Reorientation of the nanocrystallites and the global reorientation of the PTB7 polymer chain were observed along the stretching direction up to 100% strain, which was reversible as the blend was allowed to relax to 0% strain. The polymer solar cell based on PTB7:PC71BM:DIO with such reversible morphological changes exhibited a rubbery elasticity at room temperature. The device could be stretched up to 100% strain, and the power-conversion efficiency shows a slight increase up to 30% strain and a global increase of power generation as the photoactive area increases with strain. Solar cells were fabricated employing a layer of the PTB7:PC71BM:DIO blend sandwiched between a pair of stretchable transparent electrodes, each comprising a stack of a silver nanowire percolation network and a single-wall carbon nanotube network embedded in the surface of a poly(urethane acylate) elastomer film. The solar cells were semitransparent and could be stretched like a rubbery film by as much as 100% strain. The measured power-conversion efficiency was 3.48%, which was increased to 3.67% after one cycle of stretching to 50% strain and lowered to 2.99% after 100 stretching cycles. The total power generation from the cells was significantly increased, thanks to the expanded active area as the cells were stretched.

[1]  Suchol Savagatrup,et al.  Mechanical Properties of Organic Semiconductors for Stretchable, Highly Flexible, and Mechanically Robust Electronics. , 2017, Chemical reviews.

[2]  John A Rogers,et al.  In‐Plane Deformation Mechanics for Highly Stretchable Electronics , 2017, Advanced materials.

[3]  Q. Pei,et al.  Elastomeric Light Emitting Polymer Enhanced by Interpenetrating Networks. , 2016, ACS applied materials & interfaces.

[4]  Long Ye,et al.  Molecular Design of Benzodithiophene-Based Organic Photovoltaic Materials. , 2016, Chemical reviews.

[5]  Hongbin Wu,et al.  Recent Advances in Organic Photovoltaics: Device Structure and Optical Engineering Optimization on the Nanoscale. , 2016, Small.

[6]  Cheng Wang,et al.  Flexible, highly efficient all-polymer solar cells , 2015, Nature Communications.

[7]  김재한,et al.  Highly Efficient All-Polymer Solar Cells , 2015 .

[8]  Adam D. Printz,et al.  [70]PCBM and Incompletely Separated Grades of Methanofullerenes Produce Bulk Heterojunctions with Increased Robustness for Ultra-Flexible and Stretchable Electronics , 2015 .

[9]  T. Russell,et al.  New insights into morphology of high performance BHJ photovoltaics revealed by high resolution AFM. , 2014, Nano letters.

[10]  Guillermo C Bazan,et al.  Bulk heterojunction solar cells: morphology and performance relationships. , 2014, Chemical reviews.

[11]  Darren J. Lipomi,et al.  Best of Both Worlds: Conjugated Polymers Exhibiting Good Photovoltaic Behavior and High Tensile Elasticity , 2014 .

[12]  Daniel J. Burke,et al.  Mechanical Properties of Conjugated Polymers and Polymer‐Fullerene Composites as a Function of Molecular Structure , 2014 .

[13]  Luping Yu,et al.  Photovoltaic Function and Exciton/Charge Transfer Dynamics in a Highly Efficient Semiconducting Copolymer , 2014 .

[14]  H. Sirringhaus,et al.  Electrooptical Spectroscopy of Uniaxially Aligned Polythiophene Films in Field-Effect Transistors , 2013 .

[15]  Bethany I Lemanski,et al.  Correlating Stiffness, Ductility, and Morphology of Polymer:Fullerene Films for Solar Cell Applications , 2013 .

[16]  Zhenan Bao,et al.  Toward mechanically robust and intrinsically stretchable organic solar cells: Evolution of photovoltaic properties with tensile strain , 2012 .

[17]  Igor Sokolov,et al.  Quantitative mapping of the elastic modulus of soft materials with HarmoniX and PeakForce QNM AFM modes. , 2012, Langmuir : the ACS journal of surfaces and colloids.

[18]  Miao Xu,et al.  Enhanced power-conversion efficiency in polymer solar cells using an inverted device structure , 2012, Nature Photonics.

[19]  Feng Liu,et al.  On the morphology of polymer‐based photovoltaics , 2012 .

[20]  R. Dauskardt,et al.  Film stresses and electrode buckling in organic solar cells , 2012 .

[21]  Nicolas C. Pégard,et al.  Wrinkles and deep folds as photonic structures in photovoltaics , 2012, Nature Photonics.

[22]  Talha M. Khan,et al.  A Universal Method to Produce Low–Work Function Electrodes for Organic Electronics , 2012, Science.

[23]  M. Kaltenbrunner,et al.  Ultrathin and lightweight organic solar cells with high flexibility , 2012, Nature Communications.

[24]  W R Broughton,et al.  The use of the PeakForceTM quantitative nanomechanical mapping AFM-based method for high-resolution Young's modulus measurement of polymers , 2011 .

[25]  Zhibin Yu,et al.  Silver Nanowire‐Polymer Composite Electrodes for Efficient Polymer Solar Cells , 2011, Advanced materials.

[26]  Qibing Pei,et al.  Intrinsically Stretchable Polymer Light‐Emitting Devices Using Carbon Nanotube‐Polymer Composite Electrodes , 2011, Advanced materials.

[27]  Zhenan Bao,et al.  Stretchable, elastic materials and devices for solar energy conversion , 2011 .

[28]  Benjamin C. K. Tee,et al.  Stretchable Organic Solar Cells , 2011, Advanced materials.

[29]  G. Vancso,et al.  Quantitative mapping of elastic moduli at the nanoscale in phase separated polyurethanes by AFM , 2011 .

[30]  H. Fong,et al.  Photoluminescence anisotropy of uni-axially aligned electrospun conjugated polymer nanofibers of MEH-PPV and P3HT , 2011 .

[31]  Martin Heeney,et al.  Correlations between mechanical and electrical properties of polythiophenes. , 2010, ACS nano.

[32]  Gang Li,et al.  For the Bright Future—Bulk Heterojunction Polymer Solar Cells with Power Conversion Efficiency of 7.4% , 2010, Advanced materials.

[33]  Jan Fyenbo,et al.  Manufacture, integration and demonstration of polymer solar cells in a lamp for the “Lighting Africa” initiative , 2010 .

[34]  Gang Li,et al.  “Solvent Annealing” Effect in Polymer Solar Cells Based on Poly(3‐hexylthiophene) and Methanofullerenes , 2007 .

[35]  Xiong Gong,et al.  Thermally Stable, Efficient Polymer Solar Cells with Nanoscale Control of the Interpenetrating Network Morphology , 2005 .