Wind barriers optimization for minimizing collector mirror soiling in a parabolic trough collector plant

Abstract Wind barriers, according to their sizes and shapes, can effectively control, shift and even modify the airflow field in their downstream. These structures can accelerate the wind flow over the mirror field and move the airborne particles away from the mirrors. For example, in concentrated solar power plants it is highly desirable to engineer the system in a way that fewer particles are deposited within the solar field, in particular, onto mirror surfaces. Therefore, design optimization of dust barriers could significantly impact the mirror soiling and favourably reduce the cleaning water consumption of a solar power plant. This study focuses on the optimization of a solid wind barrier around a parabolic trough collector plant for their protection against dust soiling. The presented simulation results show that an optimum solid wind barrier is able to direct large amount of particles (in this study, more than 86%) to pass over the solar field with very small fraction (around 0.8%) being deposited on the mirrors. In addition, it was found that the barrier wall is more effective in deflecting the larger particles from the solar field.

[1]  A. Fernández-García,et al.  The design of dust barriers to reduce collector mirror soiling in CSP plants , 2018 .

[2]  David F. Fletcher,et al.  Wind engineering analysis of parabolic trough solar collectors: The effects of varying the trough depth , 2014 .

[3]  William David Lubitz,et al.  Effect of manual tilt adjustments on incident irradiance on fixed and tracking solar panels , 2011 .

[4]  Salah Abdallah,et al.  A parabolic solar cooker with automatic two axes sun tracking system , 2010 .

[5]  H. Almond,et al.  Predicting the Effects of Sand Erosion on Collector Surfaces in CSP Plants , 2015 .

[6]  R. Bagnold,et al.  The Physics of Blown Sand and Desert Dunes , 1941 .

[7]  Martin Rein,et al.  Cold spray deposition: Significance of particle impact phenomena , 2005 .

[8]  M. M. El-Kassaby.  Prediction of Optimum Tilt Angle for Parabolic Trough with the Long Axis in the North-South Direction , 1994 .

[9]  Tijani Bounahmidi,et al.  Benchmark of Concentrating Solar Power Plants: Historical, Current and Future Technical and Economic Development , 2016, ANT/SEIT.

[10]  K. A. Antonopoulos,et al.  Thermal enhancement of solar parabolic trough collectors by using nanofluids and converging-diverging absorber tube , 2016 .

[11]  Thomas E. Gill,et al.  Land use/land cover and point sources of the 15 December 2003 dust storm in southwestern North America , 2009 .

[12]  J. Meyer,et al.  Heat transfer and thermodynamic performance of a parabolic trough receiver with centrally placed perforated plate inserts , 2014 .

[13]  Markus Eck,et al.  Maximum temperature difference in horizontal and tilted absorber pipes with direct steam generation , 2004 .

[14]  Josua P. Meyer,et al.  Thermodynamic optimisation of the performance of a parabolic trough receiver using synthetic oil–Al2O3 nanofluid , 2015 .

[15]  G. C. Bakos,et al.  Design and construction of a two-axis Sun tracking system for parabolic trough collector (PTC) efficiency improvement , 2006 .

[16]  T. Stathopoulos,et al.  CFD simulation of the atmospheric boundary layer: wall function problems , 2007 .

[17]  K. R. Kumar,et al.  Thermal analysis of solar parabolic trough with porous disc receiver , 2009 .

[18]  M. Yaghoubi,et al.  A novel experimental method to find dust deposition effect on the performance of parabolic trough solar collectors , 2012 .

[19]  Jie Sun,et al.  Test of a solar parabolic trough collector with rotatable axis tracking , 2017 .

[20]  Gianpiero Colangelo,et al.  Results of experimental investigations on the heat conductivity of nanofluids based on diathermic oil for high temperature applications , 2012 .

[21]  Peter Richards,et al.  Appropriate boundary conditions for computational wind engineering models revisited , 2011 .

[22]  J. Meseguer,et al.  On the effects of windbreaks on the aerodynamic loads over parabolic solar troughs , 2014 .

[23]  J. Muñoz,et al.  Analysis of internal helically finned tubes for parabolic trough design by CFD tools , 2011 .

[24]  Goodarz Ahmadi,et al.  Aerosol particle deposition in an obstructed turbulent duct flow , 1994 .

[25]  Yi Zhang,et al.  Calculating the Optimum Tilt Angle for Parabolic Solar Trough Concentrator with  the North-South Tilt Tracking Mode , 2013, 2013 Fourth International Conference on Digital Manufacturing & Automation.

[26]  G. Ahmadi,et al.  Particle deposition in turbulent duct flows—comparisons of different model predictions , 2007 .

[27]  Chang Xu,et al.  Numerical study of heat transfer enhancement in the receiver tube of direct steam generation with parabolic trough by inserting metal foams , 2013 .

[28]  K. Nyembwe,et al.  Physical properties of sand parts produced using a Voxeljet VX1000 three-dimensional printer , 2016 .

[29]  Eduardo Zarza,et al.  Parabolic-trough solar collectors and their applications , 2010 .

[30]  Josua P. Meyer,et al.  Optimal thermal and thermodynamic performance of a solar parabolic trough receiver with different nanofluids and at different concentration ratios , 2017 .

[31]  Lin Lu,et al.  Analyzing wind cleaning process on the accumulated dust on solar photovoltaic (PV) modules on flat surfaces , 2018 .

[32]  E. Bellos,et al.  Multi-criteria evaluation of parabolic trough collector with internally finned absorbers , 2017 .

[33]  M. Moghimi,et al.  Optimization of a trapezoidal cavity absorber for the Linear Fresnel Reflector , 2015 .

[34]  M. Moghimi,et al.  Simulation-based optimisation of a linear Fresnel collector mirror field and receiver for optical, thermal and economic performance , 2017 .