Assessment of Gearbox Operational Loads and Reliability under High Mean Wind Speeds

Abstract This paper investigates the dynamic loads occurring in the drivetrain of wind turbines with a focus on offshore applications. Herein a model of the gearbox of the 5 MW wind turbine is presented. The model is developed in a multi-body framework using commercial software MSC ADAMS. Validation of the model was based on the experimental data provided by NREL for 750 kW prototype gearbox. Failures of gearboxes caused by high dynamic loads have a significant influence on the cost of operation of wind farms. For these reasons in the study, the probability of failure of the gearbox working in an offshore wind turbine that operates in storm conditions with mean wind speeds less than 30 m/s is presented. In the study, normal shut-downs of a wind turbine in storm conditions were investigated. The analysis were conducted for two storm control strategies and different wind conditions from an extreme operating gust, normal turbulence model and extreme turbulence model. In the paper, loads in the planetary gear are quantified as well as the torsional moments in the main shaft. On the basis of simulation results the annual probability of failure of the gearbox in a wind turbine with soft storm controller is calculated, and compared with the one had the gearbox working in a wind turbine operating with hard storm controller. In the study, it was found that normal shut-downs do not have a significant influence on the ultimate loads in the gearbox, since they are related mostly to the gusts occurring during turbulence. Application of the storm controller with reduction of the wind turbine power allowed the decrease of the probability of failure for ultimate stresses.

[1]  Torgeir Moan,et al.  On long-term fatigue damage and reliability analysis of gears under wind loads in offshore wind turbine drivetrains , 2014 .

[2]  Dariusz Ceglarek,et al.  Comparative Analysis of Tooth-Root Strength Using ISO and AGMA Standards in Spur and Helical Gears With FEM-based Verification , 2006 .

[3]  F. Oyague,et al.  Gearbox Modeling and Load Simulation of a Baseline 750-kW Wind Turbine Using State-of-the-Art Simulation Codes , 2009 .

[4]  T. A. Harris,et al.  Rolling Bearing Analysis , 1967 .

[5]  G. Mandic,et al.  Active Torque Control for Gearbox Load Reduction in a Variable-Speed Wind Turbine , 2012, IEEE Transactions on Industry Applications.

[6]  Zahra Hashemiyan,et al.  Model of the Planetary Gear Based on Multi-Body Method and Its Comparison with Experiment on the Basis of Gear Meshing Frequency and Sidebands , 2014 .

[7]  John Dalsgaard Sørensen,et al.  Influence of the control system on wind turbine reliability in extreme turbulence , 2014 .

[8]  S. Butterfield,et al.  Improving Wind Turbine Gearbox Reliability , 2007 .

[9]  D. Kong,et al.  Nonlinear Contact Analysis of Gear Teeth for Malfunction Diagnostics , 2008 .

[10]  W. LaCava,et al.  Gearbox Reliability Collaborative Project Report: Findings from Phase 1 and Phase 2 Testing , 2011 .

[11]  Lorenzo Zeni,et al.  Reliability of offshore wind power production under extreme wind conditions. Deliverable D 9.5. Work Package 9: Electrical grid , 2010 .

[12]  J. Jonkman,et al.  Definition of a 5-MW Reference Wind Turbine for Offshore System Development , 2009 .

[13]  John Dalsgaard Sørensen,et al.  Upscaling Wind Turbines: theoretical and practical aspects and their impact on the cost of energy , 2012 .

[14]  Jan Adamczyk,et al.  Analysis of vibrations generated by the multi-body model of a planetary gear , 2012 .

[15]  W. Cioch,et al.  Model of the Gears Based on Multibody System and Its Validation by Application of Non-Contact Methods , 2013 .