Switchable low-loss RF MEMS Ka-band frequency-selective surface

A switchable frequency-selective surface (FSS) was developed at 30 GHz using RF microelectromechanical systems (MEMS) switches on a 500-/spl mu/m-thick glass substrate. The 3-in-diameter FSS is composed of 909 unit cells and 3636 MEMS bridges with a yield of 99.5%. The single-pole FSS shows a transmission loss of 2.0 dB and a -3-dB bandwidth of 3.2 GHz at a resonant frequency of 30.2 GHz with the MEMS bridges in the up-state position. The -1-dB bandwidth is 1.6 GHz. When the MEMS bridges are actuated to the down-state position, an insertion loss of 27.5 dB is measured. Theory and experiment agree quite well. The power handling is limited to approximately 25 W with passive air cooling and >150 W with active air cooling due to the increased temperature of the overall circuit resulting from the transmission loss (for continuous-wave operation with the assumed maximum allowable temperature of 80/spl deg/C), or 370 W-3.5 kW due to self-actuation of the RF MEMS bridges (for pulsed incident power). Experimental results validate that 20 W of continuous-wave power can be transferred by the RF MEMS FSS with no change in the frequency response. This is the first demonstration of a switched low-loss FSS at Ka-band frequencies.

[1]  J.R. Reid,et al.  RF actuation of capacitive MEMS switches , 2003, IEEE MTT-S International Microwave Symposium Digest, 2003.

[2]  Te-kao Wu,et al.  Multiband frequency selective surface with multiring patch elements , 1994 .

[3]  K. D. Stephan,et al.  Quasioptical millimeter-wave hybrid and monolithic PIN diode switches , 1993 .

[4]  David M. Pozar,et al.  Radiation and scattering characteristics of microstrip antennas on normally biased ferrite substrates , 1992 .

[5]  Gabriel M. Rebeiz,et al.  Steady state thermal analysis and high-power reliability considerations of RF MEMS capacitive switches , 2002, 2002 IEEE MTT-S International Microwave Symposium Digest (Cat. No.02CH37278).

[6]  W. R. Bushelle,et al.  Development of a resonant metal radome , 1978 .

[7]  Christos Mias.  Frequency selective surfaces loaded with surface-mount reactive components , 2003 .

[8]  R. Elliott.  Antenna Theory and Design , 2003 .

[9]  Richard J. Langley,et al.  Influence of supporting dielectric layers on the transmission properties of frequency selective surfaces , 1991 .

[10]  Laurent Dussopt,et al.  Miniature and tunable filters using MEMS capacitors , 2003 .

[11]  J. C. Vardaxoglou,et al.  Frequency Selective Surfaces in Dual and Triple Band Offset Reflector Antennas , 1987, 1987 17th European Microwave Conference.

[12]  R. Langley,et al.  Frequency selective surfaces on biased ferrite substrates , 1994 .

[13]  Gabriel M. Rebeiz,et al.  Very low-loss distributed X-band and Ka-band MEMS phase shifters using metal-air-metal capacitors , 2003 .

[14]  Y. Rahmat-Samii,et al.  MEMS enabled reconfigurable frequency selective surfaces: design, simulation, fabrication, and measurement , 2002, IEEE Antennas and Propagation Society International Symposium (IEEE Cat. No.02CH37313).

[15]  T. Leonard,et al.  Frequency selective surfaces , 1977 .

[16]  Richard J. Langley,et al.  Active frequency-selective surfaces , 1996 .

[17]  G.M. Rebeiz,et al.  Switchable RF MEMS Ka-band frequency-selective surface , 2004, 2004 IEEE MTT-S International Microwave Symposium Digest (IEEE Cat. No.04CH37535).