Three dimensional discrete element models for simulating the filling and emptying of silos: Analysis of numerical results

Abstract The discrete element method (DEM) is a promising technique that allows the mechanical behaviour of the material stored in silos and hoppers to be studied. The present work analyses the numerical results obtained by two three-dimensional DEM models that simulate the filling and discharge of a silo for two materials: glass beads or maize grains. The aim of the present work was to assess the capacity of these models to predict the behaviour of the studied materials. To guarantee the maximum representativeness of the results, many of the simplifications usually used in DEM models were avoided. The results analysed included the vertical distributions of the normal pressure, tangential pressure and mobilised friction, the horizontal distribution of normal pressure, velocity profiles and the spatial distribution of the bulk density. The results of this analysis highlight the potential of DEM models for studying the behaviour of granular materials in silos and hoppers, provided that simplifications are minimized.

[1]  C. González-Montellano,et al.  Validation and experimental calibration of 3D discrete element models for the simulation of the discharge flow in silos , 2011 .

[2]  C. González-Montellano,et al.  Numerical effects derived from en masse filling of agricultural silos in DEM simulations , 2012 .

[3]  P. Aguado,et al.  SE—Structures and Environment: Static and Dynamic Silo Loads using Finite Element Models , 2001 .

[4]  Icíar Alfaro,et al.  Simulation of axisymmetric discharging in metallic silos. Analysis of the induced pressure distribution and comparison with different standards , 2002 .

[5]  Bruno C. Hancock,et al.  Granular segregation in discharging cylindrical hoppers: A discrete element and experimental study , 2007 .

[6]  Zenon Mróz,et al.  Investigation of wall stress and outflow rate in a flat-bottomed bin: A comparison of the DEM model results with the experimental measurements , 2011 .

[7]  Aibing Yu,et al.  Numerical investigation of steady and unsteady state hopper flows , 2006 .

[8]  J. De Baerdemaeker,et al.  Discrete element modelling for process simulation in agriculture , 2003 .

[9]  C. González-Montellano,et al.  Discrete element modelling of grain flow in a planar silo: influence of simulation parameters , 2011 .

[10]  P. A. Langston,et al.  Discrete element simulation of granular flow in 2D and 3D hoppers: Dependence of discharge rate and wall stress on particle interactions , 1995 .

[11]  J. M. Rotter,et al.  Verification of a 3-dimensional model for filling pressures in square thin-walled silos , 2003 .

[12]  S. Masson,et al.  Effect of particle mechanical properties on silo flow and stresses from distinct element simulations , 2000 .

[13]  P. Cundall,et al.  A discrete numerical model for granular assemblies , 1979 .

[14]  Fritz Ebert,et al.  Three-dimensional discrete element simulations in hoppers and silos , 2005 .

[15]  D. Maza,et al.  The flow rate of granular materials through an orifice , 2007, 0707.4550.

[16]  Francisco Ayuga,et al.  Pressure measurements in steel silos with eccentric hoppers , 2010 .

[17]  Martin R. Wolf,et al.  K3 User Guide , 2000 .

[18]  Mohammad Hossein Abbaspour-Fard,et al.  Shape representation of axi‐symmetrical, non‐spherical particles in discrete element simulation using multi‐element model particles , 1999 .

[19]  Jan C. Jofriet,et al.  A Numerical Model for Flow of Granular Materials in Silos. Part 1: Model Development , 1997 .

[20]  Yutaka Tsuji,et al.  Lagrangian numerical simulation of plug flow of cohesionless particles in a horizontal pipe , 1992 .

[21]  Bruno C. Hancock,et al.  Optimizing the design of eccentric feed hoppers for tablet presses using DEM , 2010, Comput. Chem. Eng..

[22]  Francisco Ayuga,et al.  Simulations of granular flow in silos with different finite element programs: ANSYS vs. SILO. , 2010 .

[23]  James W. Landry,et al.  Discrete element simulations of stress distributions in silos: crossover from two to three dimensions , 2003 .

[24]  J. Ooi,et al.  Experiments and simulations of direct shear tests: porosity, contact friction and bulk friction , 2008 .

[25]  Jin Y. Ooi,et al.  The influence of a cone-in-cone insert on flow pattern and wall pressure in a full-scale silo , 2008 .

[26]  Francisco Ayuga,et al.  Some unresolved problems in the design of steel cylindrical silos , 2008 .

[27]  J. M. Rotter,et al.  Experiments on a square planform steel silo , 2000 .

[28]  J. M. Rotter,et al.  Steel silos with different aspect ratios: II – behaviour under eccentric discharge , 2014 .

[29]  Itzhak Shmulevich,et al.  Determination of discrete element model parameters required for soil tillage , 2007 .

[30]  C. Thornton,et al.  A comparison of discrete element simulations and experiments for ‘sandpiles’ composed of spherical particles , 2005 .

[31]  Francisco Ayuga,et al.  Finite element analysis under different boundary conditions of the filling of cylindrical steel silos having an eccentric hopper , 2008 .

[32]  J. Z. Zhu,et al.  The finite element method , 1977 .