Laboratory research facility for testing hydrodynamic thrust bearings

Abstract A research facility has been designed and manufactured to study performance characteristics of industrial hydrodynamic thrust bearings. The facility includes a test rig containing two identical tilting pad thrust bearings operating against separate collars. A shaft supported by two journal bearings is driven by a 143kW variable-speed d.c. motor. The bearings are tested in a balanced pair to accommodate the substantial axial force generated by hydraulic cylinders. Bearing instrumentation encompasses a distribution of thermocouples, pressure transducers and oil-film thickness sensors of eddy current type. Two piezoelectric transducers for pressure profile measurements and three thermistors are mounted in one of the shaft collars. Additional instrumentation includes thermocouples, pressure sensors, flowmeters, a load cell and inductive sensors. Signals from all sensors are logged by a personal computer-based high-speed data acquisition system that acquires the measured data, conditions them and presents the results on line. Power losses are obtained by monitoring bearing friction torque and by the calorimetric technique. A detailed description of the research facility is provided together with some representative results of equalizing tilting pad thrust bearing performance obtained for the steady state and transient operating conditions.

[1]  Sergei B. Glavatskikh,et al.  Steady State Performance Characteristics of a Tilting Pad Thrust Bearing , 2001 .

[2]  N. H. New.  Experimental Comparison of Flooded, Directed, and Inlet Orifice Type of Lubrication for a Tilting Pad Thrust Bearing , 1974 .

[3]  Michał Wasilczuk,et al.  A Method of Friction Torque Measurement for a Hydrodynamic Thrust Bearing , 1995 .

[4]  A. Cameron,et al.  Studies in hydronamic thrust bearings II. Comparison of calculated and measured performance of tilting pads by means of interferometry , 1975, Philosophical Transactions of the Royal Society of London. Series A, Mathematical and Physical Sciences.

[5]  Kyung-Woong Kim,et al.  AN EXPERIMENTAL-STUDY ON THE THERMOHYDRODYNAMIC LUBRICATION OF TILTING-PAD THRUST-BEARINGS , 1995 .

[6]  A. K. Tieu.  Hydrodynamic Thrust Bearings: Theory and Experiment , 1991 .

[7]  Sergei Glavatskih,et al.  Simultaneous monitoring of oil film thickness and temperature in fluid film bearings , 2000 .

[8]  J. B. Medley,et al.  Spring-Supported Thrust Bearings Used in Hydroelectric Generators: Laboratory Test Facility© , 1999 .

[9]  R. S. Gregory.  Performance of Thrust Bearings at High Operating Speeds , 1974 .

[10]  R. E. Gustafson.  Behavior of a Pivoted-Pad Thrust Bearing During Start-Up , 1967 .

[11]  J. E. L. Simmons,et al.  Measurements of Maximum Temperature in Tilting-Pad Thrust Bearings , 1988 .

[12]  W. W. Gardner.  Performance Tests on Six-Inch Tilting Pad Thrust Bearings , 1975 .

[13]  Sergei B. Glavatskikh.  Transient thermal effects in a pivoted pad thrust bearing , 2000 .

[14]  TEHD analysis of tilting-pad thrust bearings-comparison with experimental data , 2001 .

[15]  E. W. Hemingway,et al.  The Measurement of Film Thickness in Thrust Bearings and the Deflected Shape of ‘Parallel’ Surface Thrust Pads , 1965 .

[16]  R. Larsson,et al.  THD Analysis of Tilting Pad Thrust Bearings—Comparison Between Theory and Experiments , 2000 .

[17]  Paola Forte,et al.  An investigation on thrust bearing tilting pads , 1998 .

[18]  A. K. Tieu.  An Investigation of “Diaphragm” Type Thrust Bearings—Part I: Experiment , 1975 .

[19]  P B Neal.  Heat Transfer in PAD Thrust Bearings , 1982 .

[20]  C. F. Kettleborough,et al.  Micheli Bearing Lubrication*: Part I—Experimental Results: Part II—Correlation between Theory and Experiment , 1955 .

[21]  J. W. Capitao.  Performance Characteristics of Tilting Pad Thrust Bearings at High Operating Speeds , 1976 .

[22]  J. W. Capitao,et al.  Effects of High-Operating Speeds on Tilting Pad Thrust Bearing Performance , 1976 .