Nonisothermal model for gas separation hollow-fiber membranes

A model for multicomponent gas separation using hollow-fiber membrane modules is presented that explicitly accounts for heating or cooling inside membrane permeators due to gas expansion. The model permits simulation of countercurrent contacting with permeate purging (or sweep). The numerical approach permits rapid and stable solutions for cases with many components, even when the mixture contains components with widely varying permeability coefficients. Simulation results are presented for natural-gas sweetening, a commercially significant application, using polymer permeation properties similar to those of a high-performance polyimide. For some conditions, temperature decreases from the feed to residue end of the module by as much as 40 C. As CO{sub 2} concentration in the feed increases or as stage cut increases, the temperature decrease from feed to residue increases. Relative to an isothermal case, expansion-driven cooling reduces stage cut at a given feed flow rate since gas permeability decreases with decreasing temperature. Neglect of expansion-driven cooling in natural-gas separation simulations can lead to large errors in estimating the amount of feed gas that can be treated to achieve a fixed residue composition. For 30% CO{sub 2} feed concentration, if the effective membrane thickness is halved, only a 20% increase (rather than almost a factormore » of 2) in the amount of gas that can be treated per unit area is obtained due to the impact of expansion-driven cooling on gas flux.« less

[1]  Benny D. Freeman,et al.  Modeling multicomponent gas separation using hollow‐fiber membrane contactors , 1998 .

[2]  Benny D. Freeman,et al.  Corrections for analytical gas-permeation models for separation of binary gas mixtures using membrane modules , 1996 .

[3]  Benny D. Freeman,et al.  Gas separation using polymer membranes: an overview , 1994 .

[4]  David R. Lide,et al.  CRC HANDBOOK of THERMOPHYSICAL and THERMOCHEMICAL DATA , 1994 .

[5]  S. A. Stern,et al.  Membrane processes for the removal of acid gases from natural gas. II. Effects of operating conditions, economic parameters, and membrane properties , 1993 .

[6]  S. A. Stern,et al.  Membrane processes for the removal of acid gases from natural gas. I. Process configurations and optimization of operating conditions , 1993 .

[7]  A. Cornelissen.  Heat effect in gas permeation, with special reference to spiral-wound modules , 1993 .

[8]  A. Khan,et al.  Models and analyses of membrane gas permeators , 1992 .

[9]  A. Khan,et al.  Approximate solutions for gas permeators separating binary mixtures , 1992 .

[10]  R. Reid,et al.  The Properties of Gases and Liquids , 1977 .

[11]  S. R. Auvil,et al.  Asymptotic analysis of gas separation by a membrane module , 1988 .

[12]  Hans J Gorissen,et al.  Temperature changes involved in membrane gas separations , 1987 .

[13]  Robert Rautenbach,et al.  Gas permeation — module design and arrangement , 1987 .

[14]  C. Pan.  Gas separation by high‐flux, asymmetric hollow‐fiber membrane , 1986 .

[15]  K. Sirkar,et al.  Series solutions for a gas permeator with countercurrent and cocurrent flow , 1984 .

[16]  W. Koros,et al.  Energetics of gas sorption in glassy polymers , 1979 .

[17]  C. L. Tien,et al.  Fundamental principles of heat transfer , 1977 .

[18]  P. O. Backer,et al.  Enrichment calculations in gaseous diffusion: Large separation factor , 1955 .

[19]  R. M. Barrer.  Permeability in relation to viscosity and structure of rubber , 1942 .

[20]  J. S. Rowlinson,et al.  Molecular Thermodynamics of Fluid-Phase Equilibria , 1969 .

[21]  J. Smith,et al.  Introduction to chemical engineering thermodynamics , 1949 .

[22]  Thomas Graham F.R.S..  LXIX. On the absorption and dialytic separation of gases by colloid septa , 1866 .