A novel method to predict the pull-in voltage in a closed form for micro-plates actuated by a distributed electrostatic force

This study is devoted to finding the precise pull-in voltage/position of a micro-device formed by two parallel charged plates. Pull-in is a phenomenon where the electrostatic force induced by the applied voltage across two plates of the device exceeds the elastic, restoring force exerted by the deformed plates, leading to a contact between the two plates. To offer a precise prediction of the pull-in, a dynamic model in the form of a partial differential equation (PDE) is established based on the equilibrium among plate flexibility, residual stress and distributed electrostatic forces. The Galerkin method is employed to decompose the established PDE into discrete modal equations. By considering lower order modes and solving them, one arrives at a prediction of plate deflection in terms of the applied bias voltage. Approximating the solved deflection by a fifth-order series and full-order numerical integration, the pull-in position and voltage are successfully approximated. The pull-in position in terms of center deflection of the deformed plate is found to be 48% of the air gap between the plates, which presents a better estimation than the commonly used one-third of the gap derived by all past studies based on a less realistic one-dimensional lump model. A closed form of the pull-in voltage is derived to offer design guidelines for the device prior to production. The aforementioned theoretical findings are finally validated by finite element and experimental studies on a MEMS device of parallel charged micro-plates designed and fabricated in the laboratory.

[1]  M. Younis,et al.  A new approach to the modeling and simulation of flexible microstructures under the effect of squeeze-film damping , 2004 .

[2]  W. Grabinski,et al.  Electrical modeling of a pressure sensor MOSFET , 2001 .

[3]  Richard S. Muller,et al.  Piezoelectric microphone with on-chip CMOS circuits , 1993 .

[4]  A. Dehe,et al.  AC transfer function of electrostatic capacitive sensors based on the 1-D equivalent model: application to silicon microphones , 2003 .

[5]  A. Dehe,et al.  Constant charge operation of capacitor sensors based on switched-current circuits , 2003 .

[6]  Ai Qun Liu,et al.  MEMS widely tunable lasers for WDM system applications , 2002, SPIE/OSA/IEEE Asia Communications and Photonics.

[7]  Precision wavelength light sources for dense WDM system , 1997, Photonics West.

[8]  Ali H. Nayfeh,et al.  A reduced-order model for electrically actuated microbeam-based MEMS , 2003 .

[9]  Ali H. Nayfeh,et al.  A reduced-order model for electrically actuated clamped circular plates , 2005 .

[10]  Wouter Olthuis,et al.  A silicon condenser microphone with polyimide diaphragm and backplate , 1997 .

[11]  S. Krylov,et al.  Pull-in Dynamics of an Elastic Beam Actuated by Continuously Distributed Electrostatic Force , 2004 .

[12]  Wouter Olthuis,et al.  High-performance condenser microphone with fully integrated CMOS amplifier and DC-DC voltage converter , 1998 .

[13]  S.D. Senturia,et al.  Computer-aided generation of nonlinear reduced-order dynamic macromodels. I. Non-stress-stiffened case , 2000, Journal of Microelectromechanical Systems.

[14]  Ali H. Nayfeh,et al.  Modeling and simulations of thermoelastic damping in microplates , 2004 .

[15]  Jin Cheng,et al.  Analytical and finite element model pull-in study of rigid and deformable electrostatic microactuators , 2004 .

[16]  Ming-Shaung Ju,et al.  Development of a microelectromechanical system pressure sensor for rehabilitation engineering applications , 2000 .

[17]  P. Bergveld,et al.  On The Electromechanical Behaviour Of Thin Perforated Backplates In Silicon Condenser Microphones , 1995, Proceedings of the International Solid-State Sensors and Actuators Conference - TRANSDUCERS '95.

[18]  R. Muller,et al.  Integrated microphone with CMOS circuits on a single chip , 1989, International Technical Digest on Electron Devices Meeting.

[19]  Ai Qun Liu,et al.  MEMS variable optical attenuator using low driving voltage for DWDM systems , 2002 .