Numerical Investigation of Masonry Strengthened with Composites

In this work, two main fiber strengthening systems typically applied in masonry structures have been investigated: composites made of basalt and hemp fibers, coupled with inorganic matrix. Starting from the experimental results on composites, the out-of-plane behavior of the strengthened masonry was assessed according to several numerical analyses. In a first step, the ultimate behavior was assessed in terms of P (axial load)-M (bending moment) domain (i.e., failure surface), changing several mechanical parameters. In order to assess the ductility capacity of the strengthened masonry elements, the P-M domain was estimated starting from the bending moment-curvature diagrams. Key information about the impact of several mechanical parameters on both the capacity and the ductility was considered. Furthermore, the numerical analyses allow the assessment of the efficiency of the strengthening system, changing the main mechanical properties. Basalt fibers had lower efficiency when applied to weak masonry. In this case, the elastic properties of the masonry did not influence the structural behavior under a no tension assumption for the masonry. Conversely, their impact became non-negligible, especially for higher values of the compressive strength of the masonry. The stress-strain curve used to model the composite impacted the flexural strength. Natural fibers provided similar outcomes, but a first difference regards the higher mechanical compatibility of the strengthening system with the substrate. In this case, the ultimate condition is due to the failure mode of the composite. The stress-strain curves used to model the strengthening system are crucial in the ductility estimation of the strengthened masonry. However, the behavior of the composite strongly influences the curvature ductility in the case of higher compressive strength for masonry. The numerical results discussed in this paper provide the base to develop normalized capacity models able to provide important information on the out-of-plane behavior of masonry elements strengthened with inorganic matrix and several kinds of fibers, both synthetic and natural.

[1]  Fernando Fraternali,et al.  On the reinforcement of cement mortars through 3D printed polymeric and metallic fibers , 2016 .

[2]  Andrea Prota,et al.  Nonlinear Analyses of Adobe Masonry Walls Reinforced with Fiberglass Mesh , 2014 .

[3]  D. Das,et al.  In-plane strength of masonry panel strengthened with geosynthetic , 2017 .

[4]  D. Ferretti,et al.  A non-linear constitutive relation for the analysis of FRCM elements , 2016 .

[5]  P. Lourenço,et al.  Shear capacity assessment of tuff panels strengthened with FRP diagonal layout , 2011 .

[6]  Yong Sheng,et al.  Evaluation of different computational modelling strategies for the analysis of low strength masonry structures , 2014 .

[7]  Andrea Prota,et al.  Seismic Strengthening of Masonry Vaults with Abutments Using Textile-Reinforced Mortar , 2016 .

[8]  Andrea Prota,et al.  Collapse analysis of slender masonry barrel vaults , 2016 .

[9]  Manicka Dhanasekar,et al.  Masonry walls under combined in-plane and out-of-plane loadings , 2018 .

[10]  A. Prota,et al.  Shaking table tests on a full-scale unreinforced and IMG-retrofitted clay brick masonry barrel vault , 2016, Bulletin of Earthquake Engineering.

[11]  Nicola Augenti,et al.  Earthquake damages to cultural heritage constructions and simplified assessment of artworks , 2013 .

[12]  Andrea Prota,et al.  Structural behaviour of masonry panels strengthened with an innovative hemp fibre composite grid , 2015 .

[13]  F. L. Wang,et al.  Research progress and low-carbon property of reinforced concrete block masonry structures in China , 2016 .

[14]  Manicka Dhanasekar,et al.  Prediction of masonry compressive behaviour using a damage mechanics inspired modelling method , 2016 .

[15]  Samuel A. Babatunde,et al.  Review of strengthening techniques for masonry using fiber reinforced polymers , 2017 .

[16]  Manicka Dhanasekar,et al.  Characterisation of cementitious polymer mortar – Auxetic foam composites , 2017 .

[17]  Manicka Dhanasekar,et al.  Out-of-plane deformation and failure of masonry walls with various forms of reinforcement , 2016 .

[19]  F. Ceroni,et al.  Use of DIC technique for investigating the behaviour of FRCM materials for strengthening masonry elements , 2017 .

[20]  F. Ceroni,et al.  Experimental tests on FRCM strengthening systems for tuff masonry elements , 2017 .

[21]  Fernando Fraternali,et al.  On the minimal mass reinforcement of masonry structures with arbitrary shapes , 2017 .

[22]  Andrea Prota,et al.  Potential of structural pozzolanic matrix–hemp fiber grid composites , 2011 .

[23]  Fernando Fraternali,et al.  MINIMAL MASS DESIGN OF STRENGTHENING TECHNIQUES FOR PLANAR AND CURVED MASONRY STRUCTURES , 2016 .

[24]  Experimental Behavior of Natural Fiber-Based Composites Used for Strengthening Masonry Structures , 2013 .

[25]  C. Poggi,et al.  Mechanical properties and debonding strength of Fabric Reinforced Cementitious Matrix (FRCM) systems for masonry strengthening , 2015 .

[26]  F. Focacci,et al.  Periodic variation of the transferable load at the FRP-masonry interface , 2015 .

[27]  M. Fagone,et al.  Round Robin Test on tensile and bond behaviour of Steel Reinforced Grout systems , 2017 .

[28]  M. Aiello,et al.  Glass fabric reinforced cementitious matrix: Tensile properties and bond performance on masonry substrate , 2017 .

[29]  Manicka Dhanasekar,et al.  A generalised damage model for masonry under compression , 2016 .

[30]  Nicola Augenti,et al.  Constitutive model selection for unreinforced masonry cross sections based on best-fit analytical moment–curvature diagrams , 2016 .

[31]  Oded Rabinovitch,et al.  Masonry walls strengthened with composite materials – dynamic out-of-plane behavior , 2008 .

[32]  F. Micelli,et al.  Experimental investigation of tensile and bond properties of Carbon-FRCM composites for strengthening masonry elements , 2017 .

[33]  Paulo B. Lourenço,et al.  Performance assessment of basalt FRCM for retrofit applications on masonry , 2017 .

[34]  C. Mazzotti,et al.  Influence of mortar joints on the behaviour of FRP materials bonded to different masonry substrates , 2017 .

[35]  Michael C. Griffith,et al.  Out-of-Plane Strengthening of Unreinforced Masonry Walls Using Near Surface Mounted Fibre Reinforced Polymer Strips , 2014 .

[36]  Fernando Fraternali,et al.  On the thrust surface of unreinforced and FRP-/FRCM-reinforced masonry domes , 2015 .

[37]  J. Ferreira,et al.  Bonding and anchoring of a CFRP reinforced render for the external strengthening of old masonry buildings , 2017 .

[38]  Mario De Stefano,et al.  Intrados strengthening of brick masonry arches with different FRCM composites: Experimental and analytical investigations , 2016 .