Characterization of the interphase in an aluminium/epoxy joint by using controlled pressure scanning electron microscopy coupled with an energy dispersive X-ray spectrometer

Abstract The aim of this work is to introduce the use of low vacuum scanning electron microscopy (LVSEM) coupled with an X-ray energy dispersive spectrometer (EDS) in the field of structural adhesives, more precisely aluminium/epoxy resin assembly. Such assembly is characterized by the creation of an interphase resulting from the metal diffusion inside the resin during cross-linking. As the performance of the final bond is strongly links by the interphase properties, fine characterization of this interphase, in particularity the evaluation of its thickness is essential to understand the macroscopic properties of the adhesive assembly. First, the EDS acquisition parameters were investigated in order to limit the sample/resin damage/degradation due to the incident electrons beam irradiation. Then a specific methodology of stacked profiles was defined to improve the precision of the measures. To evaluate the true Al diffusion profile, the impact of the interaction volume of incident electron in the material on the Al signal variation during the interface crossing was calculated and the effect of the gas pressure on the electron beam characteristic and so on the measured profiles was examinated. According to our developed methodology and data treatments, Al diffusion profile was interpreted and interphase thickness was qualitatively determined by comparison with an experimental baseline. This innovative methodology promotes the use of LVSEM–EDS in the field of adhesive structural assemblies, but also, deals with a comparative study on the effect of the gas pressure on the EDS profile analysis.

[1]  Anthony J. Kinloch,et al.  The Fatigue and Durability Behaviour of Automotive Adhesives. Part II: Failure Mechanisms , 1998 .

[2]  David C. Joy,et al.  Monte Carlo Modeling for Electron Microscopy and Microanalysis , 1995 .

[3]  G. Danilatos.  Equations of charge distribution in the environmental scanning electron microscope (ESEM) , 1990 .

[4]  P. Dubot,et al.  Adsorption of monoethanolamine on clean, oxidized and hydroxylated aluminium surfaces : a model for amine-cured epoxy/aluminium interfaces , 1994 .

[5]  R. Hässler,et al.  Improvement in strength of the aluminium/epoxy bonding joint by modification of the interphase , 2004 .

[6]  M. Malac,et al.  Radiation damage in the TEM and SEM. , 2004, Micron.

[7]  B. Khelifa,et al.  Comparative study of electron beam–gas interaction in an SEM operating at pressures up to 300Pa , 2003 .

[8]  A. Roche,et al.  Epoxy–amine/metal interphases: Influences from sharp needle-like crystal formation , 2007 .

[9]  I. Miskioglu,et al.  haracterization of the interphase in epoxy/aluminum bonds using atomic force microscopy and a nano-indenter , 2005 .

[10]  G. Danilatos.  Bibliography of environmental scanning electron microscopy , 1993, Microscopy research and technique.

[11]  S. J. B. Reed,et al.  Electron Microprobe Analysis , 1975 .

[12]  P. R. Barker,et al.  Electron scattering by gas in the scanning electron microscope , 1979 .

[13]  B. Griffin.  Effects of chamber pressure and accelerating voltage on x-ray resolution in the ESEM , 1992 .

[14]  William H. Press,et al.  Numerical recipes , 1990 .

[15]  V. Robinson.  The elimination of charging artefacts in the scanning electron microscope , 1975 .

[16]  David E. Packham,et al.  Pretreatment of aluminium: topography, surface chemistry and adhesive bond durability , 1995 .

[17]  B. M. Siegel,et al.  Physical aspects of electron microscopy and microbeam analysis , 1975 .

[18]  G. Danilatos.  Foundations of Environmental Scanning Electron Microscopy , 1988 .

[19]  V. Nassiet,et al.  Viscosity effect on epoxy-diamine/metal interphases—Part II: Mechanical resistance and durability , 2007 .

[20]  J. Verstraete,et al.  X-ray microanalysis in the environmental scanning electron microscope (ESEM): Small size particles analysis limits , 2002 .

[21]  E. Plueddemann,et al.  SILANE COUPLING AGENTS , 1982 .

[22]  W. Brockmann,et al.  Adhesion in bonded aluminium joints for aircraft construction , 1986 .

[23]  J. Shah,et al.  Amplification and noise in high‐pressure scanning electron microscopy , 1993 .

[24]  D. Newbury.  X-Ray Microanalysis in the Variable Pressure (Environmental) Scanning Electron Microscope , 2002, Journal of research of the National Institute of Standards and Technology.

[25]  G. E. Thompson,et al.  The role of electron microscopy in the study of adhesion to aluminium substrates , 1993 .

[26]  D. Grubb.  Radiation damage and electron microscopy of organic polymers , 1974 .

[27]  W. Possart,et al.  Formation and structure of epoxy network interphases at the contact to native metal surfaces , 2006 .

[28]  A. Roche,et al.  Organo-metallic complex characterization formed when liquid epoxy-diamine mixtures are applied onto metallic substrates , 2001 .

[29]  Anthony J. Kinloch,et al.  The role of the interphase in the environmental failure of adhesive joints , 2000 .

[30]  A. Roche,et al.  Formation of epoxy-diamine/metal interphases , 2002 .

[31]  L. Reimer,et al.  Scanning Electron Microscopy , 1984 .