A fast hybrid start-up process for thermally self-sustained catalyticn-butane reforming in micro-SOFC power plants

This work aims at the investigation and optimization of a hybrid start-up process for a self-sustained reactor for n-butane to syngas conversion in intermediate temperature, micro-solid oxide fuel cell (micro-SOFC) power plants. The catalytic reaction is carried out in the presence of Rh-doped Ce0.5Zr0.5O2nanoparticles in a disk-shaped reactor. For the start-up, a resistance heater is embedded inside the catalytic bed and is activated until the exothermic oxidative reaction is initiated. The self-sustained temperature and reforming performance are demonstrated to be highly dependent on the fuel to oxygen (C/O) ratio and the catalytic activity at different space times. It is shown that a C/O ratio of 0.8 is a very good choice in terms of achieved steady-state temperature, syngas selectivity and start-up time. At a reactor inlet temperature of 809 °C for a C/O ratio of 0.8 and a space time as low as 8 ms, a syngas selectivity of 69.6% and a temperature of 529 °C at the simulated micro-SOFC membrane are demonstrated. After only 15 s from ignition, a temperature of 600 °C at the reactor inlet is reached. The hybrid start-up process is optimized with respect to a specific setup as an example, but is of general nature and utility to similar systems.

[1]  L. Schmidt,et al.  Partial oxidation of alkanes over noble metal coated monoliths , 1994 .

[2]  Tetsuya Osaka,et al.  Prospects of on-chip fuel cell performance: improvement based on numerical simulation , 2011 .

[3]  Qinghua Liu,et al.  Direct biofuel low-temperature solid oxide fuel cells , 2011 .

[4]  G. Jackson,et al.  Catalytic partial oxidation of n-butane over Rh catalysts for solid oxide fuel cell applications , 2010 .

[5]  Andrew Murray,et al.  Cell cycle: A snip separates sisters , 1999, Nature.

[6]  Simulation of the Postcombustor for the Treatment of Toxic and Flammable Exhaust Gases of a Micro-Solid Oxide Fuel Cell , 2009 .

[7]  D. Poulikakos,et al.  Catalytic porous ceramic prepared in‐situ by sol‐gelation for butane‐to‐syngas processing in microreactors , 2009 .

[8]  D. Poulikakos,et al.  Modeling and optimization of catalytic partial oxidation methane reforming for fuel cells , 2005 .

[9]  L. Schmidt,et al.  Fast Lightoff of Millisecond Reactors , 2002 .

[10]  Juan Carlos Ruiz-Morales,et al.  Engineering of materials for solid oxide fuel cells and other energy and environmental applications , 2010 .

[11]  K. Kendall,et al.  Cycling of three solid oxide fuel cell types , 2007 .

[12]  N. Sammes,et al.  A functional layer for direct use of hydrocarbon fuel in low temperature solid-oxide fuel cells , 2011 .

[13]  Jennifer L. M. Rupp,et al.  Review on microfabricated micro-solid oxide fuel cell membranes , 2009 .

[14]  W. Stark,et al.  Disk-shaped packed bed micro-reactor for butane-to-syngas processing , 2008 .

[15]  Alexander Mitsos,et al.  Alternatives for Micropower Generation Processes , 2004 .

[16]  C. H. Bartholomew.  Mechanisms of catalyst deactivation , 2001 .

[17]  Zongping Shao,et al.  A thermally self-sustained micro solid-oxide fuel-cell stack with high power density , 2005, Nature.

[18]  S. A. Barnett,et al.  A direct-methane fuel cell with a ceria-based anode , 1999, Nature.

[19]  Scott A. Barnett,et al.  High efficiency electrical energy storage using a methane–oxygen solid oxide cell , 2011 .

[20]  M. Meunier,et al.  Evaluation of the Actual Working Temperature of A Single-Chamber SOFC , 2004 .

[21]  L. Schmidt,et al.  Catalytic partial oxidation of methane to syngas: staged and stratified reactors with steam addition , 2001 .

[22]  W. Stark,et al.  Flame synthesis of nanocrystalline ceria-zirconia: effect of carrier liquid. , 2003, Chemical communications.

[23]  Katsutoshi Sato,et al.  Oxidative reforming of n-C4H10 triggered at ambient temperature over reduced Ni/CeO2 , 2009 .

[24]  Takao Inoue,et al.  A Solid Oxide Fuel Cell Using an Exothermic Reaction as the Heat Source , 2001 .

[25]  L. Schmidt,et al.  High yields of synthesis gas by millisecond partial oxidation of higher hydrocarbons , 2000 .

[26]  L. Schmidt,et al.  Syngas in millisecond reactors: higher alkanes and fast lightoff , 2003 .

[27]  Mayuresh V. Kothare,et al.  A radial microfluidic fuel processor , 2005 .

[28]  M. J. Watson,et al.  A Study of the Activated Decomposition of CO2 on the Cu Component of a Cu/ZnO/Al2O3 Catalyst , 2002 .

[29]  Luca Basini,et al.  Molecular and Temperature Aspects in Catalytic Partial Oxidation of Methane , 2000 .

[30]  L. Schmidt,et al.  Production of Olefins by Oxidative Dehydrogenation of Propane and Butane over Monoliths at Short Contact Times , 1994 .

[31]  Adam Hawkes,et al.  Fuel cells for micro-combined heat and power generation , 2009 .

[32]  K. Hohn,et al.  Catalytic ignition of light hydrocarbons , 2009 .

[33]  Tetsuya Osaka,et al.  Bendable fuel cells: on-chip fuel cell on a flexible polymer substrate , 2009 .

[34]  I. Dincer,et al.  Heat-up and start-up modeling of direct internal reforming solid oxide fuel cells , 2010 .

[35]  Dimos Poulikakos,et al.  Syngas production from butane using a flame-made Rh/Ce0.5Zr0.5O2 catalyst , 2007 .

[36]  Dimos Poulikakos,et al.  A micro-solid oxide fuel cell system as battery replacement , 2008 .

[37]  Katsutoshi Sato,et al.  Oxidative Reforming of n-Butane Triggered by Spontaneous Oxidation of CeO2-x at Ambient Temperature , 2008 .

[38]  G. Jackson,et al.  Influence of thermal conditions on partial oxidation of n-butane over supported Rh catalysts , 2009 .

[39]  Dimos Poulikakos,et al.  Fast and exergy efficient start-up of micro-solid oxide fuel cell systems by using the reformer or the post-combustor for start-up heating , 2008 .

[40]  W. Stark,et al.  Flame-made nanocrystalline ceria/zirconia: structural properties and dynamic oxygen exchange capacity , 2003 .