Determination of thermal residual strain in cabled optical fiber with high spatial resolution by Brillouin optical time-domain reflectometry

Abstract The thermal residual strain induced in the cabled optical fiber is a very important factor for evaluating the reliability of optical fiber cables. In order to determine the distributed thermal residual strain in cabled optical fiber, a measurement method based on Brillouin optical time-domain reflectometry (BOTDR) system is proposed in the article. Thermal characteristics of residual strain along cabled optical fibers are investigated theoretically and experimentally based on Brillouin frequency shift (BFS) detection. The thermal residual strain along the cabled fiber, if any, can be determined with a high spatial resolution that is equal to that of the BOTDR system and can be less than a few meters. A double-coated fiber in loose optical cable was used as the test cabled optical fiber, and the experimental results were in good agreement with those predicted from the theory. It has been found that the fiber residual strain increases linearly with decreasing temperature in the range from 50 to −50 °C.

[1]  Effect of temperature cycling on the static fatigue of double-coated optical fibers , 2004 .

[2]  A. Yablon.  Optical and mechanical effects of frozen-in stresses and strains in optical fibers , 2004, IEEE Journal of Selected Topics in Quantum Electronics.

[3]  Atsuya Takahashi.  Thermal Characteristics of Access Cables Composed of Newly Designed Coated Fibers , 2006, IEICE Trans. Commun..

[4]  Zuyuan He,et al.  Proposal of Brillouin optical correlation-domain reflectometry (BOCDR). , 2008, Optics express.

[5]  X. Bao,et al.  Combined distributed temperature and strain sensor based on Brillouin loss in an optical fiber. , 1994, Optics letters.

[6]  Kenichi Asakawa,et al.  Development of optical fiber/power line composite tether cable for remotely operated unmanned submersible , 1984 .

[7]  H. Kee,et al.  All-fiber system for simultaneous interrogation of distributed strain and temperature sensing by spontaneous Brillouin scattering. , 2000, Optics letters.

[8]  Eric Udd,et al.  A fiber optic sensor for transverse strain measurement , 1999 .

[9]  Anthony W. Brown,et al.  Characterization of optical fibers for optimization of a Brillouin scattering based fiber optic sensor , 2005 .

[10]  Eric Udd.  Review of multi-parameter fiber grating sensors , 2007, SPIE Optics East.

[11]  T. Parker,et al.  A fully distributed simultaneous strain and temperature sensor using spontaneous Brillouin backscatter , 1997, IEEE Photonics Technology Letters.

[12]  Nicholas P. Lawrence,et al.  High spatial resolution microwave detection system for Brillouin-based distributed temperature and strain sensors , 2004 .

[13]  M. H. Reeve,et al.  A review of the environmental factors affecting optical cable design , 1988 .

[14]  X. Bao,et al.  Tensile strain dependence of the Brillouin gain spectrum in carbon/polyimide coated fibers. , 2007, Optics letters.

[15]  T. Horiguchi,et al.  Thermal effects on the Brillouin frequency shift in jacketed optical silica fibers. , 1990, Applied optics.

[16]  N. Shibata,et al.  Thermal characteristics of optical pulse transit time delay and fiber strain in a single-mode optical fiber cable. , 1983, Applied optics.

[17]  X. Bao,et al.  Simultaneous distributed strain and temperature measurement. , 1999, Applied optics.

[18]  Kenichi Asakawa,et al.  Development of Optical Fiber/Power Line Composite Tether Cable for a Remotely Operated Unmanned Submersible , 1984, IEEE J. Sel. Areas Commun..

[19]  Luigi Bruno,et al.  A full-field method for measuring residual stresses in optical fiber , 2006 .

[20]  Xiaoyi Bao,et al.  Effect of temperature on Brillouin gain spectrum and aging behavior in carbon/polyimide coated fiber , 2008, International Conference on Optical Fibre Sensors.

[21]  Andrew D. Yablon,et al.  Optical fiber fusion splicing , 2005 .