Self-sensing comparison of fractional slot pitch winding vs. distributed winding for FW- and FI-IPMSMs based on carrier signal injection at very low speed
暂无分享,去创建一个
Robert D. Lorenz | Kan Akatsu | David Reigosa | Yuichi Shibukawa | Natee Limsuwan | K. Akatsu | R. Lorenz | D. Reigosa | N. Limsuwan | Y. Shibukawa
[1] Joachim Holtz,et al. Acquisition of rotor anisotropy signals in sensorless position control systems , 2003 .
[2] Shinji Wakui,et al. Design and Control of a Field Intensified Interior Permanent Magnet Synchronous Machine , 2006 .
[3] Jung-Ik Ha,et al. Sensorless rotor position estimation of an interior permanent-magnet motor from initial states , 2003 .
[4] Robert D. Lorenz,et al. Carrier Signal Selection for Sensorless Control of PM Synchronous Machines at Zero and Very Low Speeds , 2008, 2008 IEEE Industry Applications Society Annual Meeting.
[5] Robert D. Lorenz,et al. Automatic Self-Commissioning for Secondary-Saliencies Decoupling in Sensorless-Controlled AC Machines Using Structured Neural Networks , 2007, 2007 IEEE International Symposium on Industrial Electronics.
[6] David Díaz Reigosa. Estudio y compensación de los efectos de la saturación y la temperatura en los métodos de control sin sensor de velocidad/posición de motores síncronos de imanes permanentes basados en el rastreo de saliencias espaciales , 2007 .
[7] Robert D. Lorenz,et al. Modeling and Adaptive Decoupling of Transient Resistance and Temperature Effects in Carrier-Based Sensorless Control of PM Synchronous Machines , 2008, 2008 IEEE Industry Applications Society Annual Meeting.
[8] Nicola Bianchi,et al. Salient-rotor PM synchronous motors for an extended flux-weakening operation range , 2000 .
[9] F. Briz,et al. A comparative analysis of pulsating vs. rotating vector carrier signal injection-based sensorless control , 2008, 2008 Twenty-Third Annual IEEE Applied Power Electronics Conference and Exposition.
[10] P. Garcia,et al. Measurement and Adaptive Decoupling of Cross-Saturation Effects and Secondary Saliencies in Sensorless-Controlled IPM Synchronous Machines , 2007, 2007 IEEE Industry Applications Annual Meeting.
[11] Alfio Consoli,et al. Industry application of zero-speed sensorless control techniques for PM synchronous motors , 2001 .
[12] Robert D. Lorenz,et al. Transducerless position and velocity estimation in induction and salient AC machines , 1994, Proceedings of 1994 IEEE Industry Applications Society Annual Meeting.
[13] Makoto Sato,et al. Loss Analysis of Permanent-Magnet Motors With Concentrated Windings—Variation of Magnet Eddy-Current Loss Due to Stator and Rotor Shapes , 2008, IEEE Transactions on Industry Applications.
[14] K. Akatsu,et al. Characteristics comparison between SPMSM and IPMSM under high flux density condition by both experimental and analysis results , 2008, 2008 International Conference on Electrical Machines and Systems.
[15] Shinji Wakui,et al. Torque and Power Density Comparison between Fractional-slot Concentrated Winding SPMSMs , 2006 .
[16] N. Bianchi,et al. Influence of rotor geometry of an interior PM motor on sensorless control feasibility , 2005, Fourtieth IAS Annual Meeting. Conference Record of the 2005 Industry Applications Conference, 2005..
[17] Seung-Ki Sul,et al. Current measurement issues in sensorless control algorithm using high frequency signal injection method , 2003, 38th IAS Annual Meeting on Conference Record of the Industry Applications Conference, 2003..
[18] R. Wrobel,et al. Impact of Rotor Design on Sensorless Position Estimation , 2006, IECON 2006 - 32nd Annual Conference on IEEE Industrial Electronics.
[19] N. Bianchi,et al. Influence of Rotor Geometry of an IPM Motor on Sensorless Control Feasibility , 2005, IEEE Transactions on Industry Applications.
[20] Thomas M. Jahns,et al. Experimental verification of optimal flux weakening in surface PM machines using concentrated windings , 2005 .
[21] D. Stone,et al. Rotor loss in permanent magnet brushless AC machines , 1999, IEEE International Electric Machines and Drives Conference. IEMDC'99. Proceedings (Cat. No.99EX272).
[22] K. Akatsu,et al. SPMSM Design Considerations for Initial Position and Magnet Polarity Estimation using Carrier Signal Injection , 2007, 2007 IEEE Industry Applications Annual Meeting.
[23] Thomas M. Jahns,et al. Analysis of Rotor Core Eddy-Current Losses in Interior Permanent Magnet Synchronous Machines , 2008, 2008 IEEE Industry Applications Society Annual Meeting.
[24] D. Howe,et al. Influence of design parameters on cogging torque in permanent magnet machines , 1997, 1997 IEEE International Electric Machines and Drives Conference Record.
[25] R.D. Lorenz,et al. Dynamic Properties of Back-emf Based Sensorless Drives , 2006, Conference Record of the 2006 IEEE Industry Applications Conference Forty-First IAS Annual Meeting.
[26] Yongdong Li,et al. Interior Permanent-Magnet Synchronous Motor Design for Improving Self-Sensing Performance at Very Low Speed , 2009, IEEE Transactions on Industry Applications.
[27] F. Briz,et al. Comparison of carrier signal voltage and current injection for the estimation of flux angle or rotor position , 1998, Conference Record of 1998 IEEE Industry Applications Conference. Thirty-Third IAS Annual Meeting (Cat. No.98CH36242).
[28] Ralph Kennel,et al. Sensorless speed and position control of synchronous machines using alternating carrier injection , 2003, IEEE International Electric Machines and Drives Conference, 2003. IEMDC'03..
[29] M. Schroedl,et al. Sensorless control of AC machines at low speed and standstill based on the "INFORM" method , 1996, IAS '96. Conference Record of the 1996 IEEE Industry Applications Conference Thirty-First IAS Annual Meeting.
[30] Paul P. Acarnley,et al. Review of position-sensorless operation of brushless permanent-magnet machines , 2006, IEEE Transactions on Industrial Electronics.