Using splitter blades to improve suction performance of centrifugal impeller pumps

A comparison between centrifugal impeller pumps with and without splitter blades in terms of suction performance is presented by experimental tests and numerical analyses. The design of both pumps was carried out by preserving the impeller meridional shape, number of blades, and volute casing. Blade shapes were obtained by adopting a 1D inverse design method. The same blade loading distribution was assumed for the full blades of both impellers, while the loading distribution of the splitter blades was modified until a close matching between the two head-capacity curves was achieved. The fulfilment of this performance requirement and the use of the same number of blades were needed to describe accurately the role played by the splitter blades in cavitation inception and development. Differently from other experimental comparisons, where previous requirements were not met, a noticeable improvement in suction performance was found at large flow rates but not at partial ones, where a small deterioration in suction performance was observed. The crucial role played by the blade thickness blockage on the incidence flow angle at the leading edge of the full blades was also investigated.

[1]  B. Neumann,et al.  The Interaction Between Geometry and Performance of a Centrifugal Pump , 2005 .

[2]  Jian Wen,et al.  Impellers of low specific speed centrifugal pump based on the draughting technology , 2010 .

[3]  M. Zangeneh,et al.  On 3D Inverse Design of Centrifugal Compressor Impellers With Splitter Blades , 1998 .

[4]  Nazım Usta,et al.  Effects of Splitter Blades on Deep Well Pump Performance , 2007 .

[5]  Giorgio Pavesi,et al.  Optimum incidence angle in centrifugal pumps and radial inflow turbines , 1998 .

[6]  Giorgio Pavesi,et al.  Numerical prediction and experimental evaluation of cavitation inception on centrifugal pump impellers , 1994 .

[7]  Mehrdad Zangeneh,et al.  Suppression of secondary flows in a mixed-flow pump impeller by application of three-dimensional inverse design method: Part 2 - Experimental validation , 1996 .

[8]  M. Zangeneh,et al.  A compressible three‐dimensional design method for radial and mixed flow turbomachinery blades , 1991 .

[9]  Mehrdad Zangeneh,et al.  Suppression of Secondary Flows in a Mixed-Flow Pump Impeller by Application of Three-Dimensional Inverse Design Method: Part 1—Design and Numerical Validation , 1996 .

[10]  D. Japikse.  Centrifugal compressor design and performance , 1996 .

[11]  M. Younsi,et al.  Influence of Splitter Blades on the Flow Field of a Centrifugal Pump:Test-Analysis Comparison , 2007 .

[12]  P. Dupont,et al.  Cavitating Flow Calculations in Industry , 2003 .

[13]  Yakup Sekmen,et al.  Energy saving in a deep well pump with splitter blade , 2006 .

[14]  F. J. Wiesner.  A Review of Slip Factors for Centrifugal Impellers , 1967 .

[15]  A. Stodola.  Steam and gas turbines , 1927 .

[16]  Mustafa Gölcü,et al.  Investigation of performance characteristics in a pump impeller with low blade discharge angle , 2005 .

[17]  Yingzi Jin,et al.  Numerical simulation of flow in centrifugal pump with complex impeller , 2011 .

[18]  David Japikse,et al.  Centrifugal pump design and performance , 1997 .

[19]  John Tuzson,et al.  Centrifugal Pump Design , 2000 .

[20]  A. Whitfield,et al.  Design of radial turbomachines , 1990 .

[21]  Akira Goto,et al.  On the Design Criteria for Suppression of Secondary Flows in Centrifugal and Mixed Flow Impellers , 1997 .