Load Identification Method Based on Interval Analysis and Tikhonov Regularization and Its Application

In order to study the dynamic force identification method of an end-plate pick of shearer, a dynamic force identification technique based on interval theory was proposed. The dynamic force interval identification model is established by describing and quantifying the identified parameters. By using the interval analysis method of the first-order Taylor expansion, the dynamic force identification is transformed into two kinds of deterministic inverse problems at the midpoint of the uncertain parameter and its gradient identification. The Tikhonov regularization method is used to solve two kinds of deterministic problems, and the upper and lower boundaries of dynamic force of the end-plate pick are determined. The results show that the deviations between the identified dynamic force and the actual dynamic force are basically within 2% and 5%, and the average uncertainties are up to 7% and 10%. Therefore, the proposed method can effectively determine the upper and lower boundaries of dynamic force of the end-plate pick, improve the solving efficiency, and provide a new research method for studying the coal rock mechanism of the pick cutting load.

[1]  C. Jiang,et al.  Optimization of structures with uncertain constraints based on convex model and satisfaction degree of interval , 2007 .

[2]  C. Jiang,et al.  Response-surface-based structural reliability analysis with random and interval mixed uncertainties , 2014 .

[3]  Leslie George Tham,et al.  Robust design of structures using convex models , 2003 .

[4]  Gerhard Müller,et al.  Treatment of arbitrarily autocorrelated load functions in the scope of parameter identification , 2013 .

[5]  Hung Nguyen-Xuan,et al.  An isogeometric finite element formulation for thermal buckling analysis of functionally graded plates , 2013 .

[6]  Ramana V. Grandhi,et al.  Two-level optimization of airframe structures using response surface approximation , 2000 .

[7]  J. Renaud,et al.  Trust region model management in multidisciplinary design optimization , 2000 .

[8]  Generalized Galileo Galilei problem in interval setting for functionally related loads , 2016 .

[9]  S. Burkhart,et al.  Identification of essential anatomic landmarks in performing arthroscopic single- and double-interval slides. , 2004, Arthroscopy : the journal of arthroscopic & related surgery : official publication of the Arthroscopy Association of North America and the International Arthroscopy Association.

[10]  Guirong Liu,et al.  Transient Responses in a Functionally Graded Cylindrical Shell to a Point Load , 2002 .

[11]  Neil Genzlinger.  A. and Q , 2006 .

[12]  Chun Sheng Liu,et al.  Study on Time-Frequency Spectrum Characteristic of Dynamic Cutting Load Based on Wavelet Regularization , 2014 .

[13]  Lee H. Keel,et al.  Interval model identification and robustness analysis for uncertain flexible structures , 1996, IEEE Trans. Control. Syst. Technol..

[14]  G. Muscolino,et al.  Interval analysis of structures with uncertain-but-bounded axial stiffness , 2011 .

[15]  Fei Lei,et al.  Structural design and global sensitivity analysis of the composite B-pillar with ply drop-off , 2018 .

[16]  Xiangyang Li,et al.  Error estimation of load identification based on linear sensitivity analysis and interval technique , 2017 .

[17]  Xu Han,et al.  An efficient method to reduce ill-posedness for structural dynamic load identification , 2017 .

[18]  Hung Nguyen-Xuan,et al.  Analysis of functionally graded plates by an efficient finite element method with node-based strain smoothing , 2012 .

[19]  W. Marsden.  I and J , 2012 .

[20]  Analysis of structures with random axial stiffness described by imprecise probability density functions , 2017 .

[21]  Chong Wang,et al.  Evidence-theory-based model validation method for heat transfer system with epistemic uncertainty , 2018, International Journal of Thermal Sciences.

[22]  Chong Wang,et al.  Novel model calibration method via non-probabilistic interval characterization and Bayesian theory , 2019, Reliab. Eng. Syst. Saf..

[23]  Chong Wang,et al.  Novel interval theory‐based parameter identification method for engineering heat transfer systems with epistemic uncertainty , 2018 .

[24]  Xu Han,et al.  Identification of the visco-hyperelastic properties of brain white matter based on the combination of inverse method and experiment , 2019, Medical & Biological Engineering & Computing.

[25]  Dun-Wei Gong,et al.  Particle swarm optimisation for multi-project location problems with interval profits , 2009, Int. J. Model. Identif. Control..

[26]  Kun Li,et al.  Identification of oil-film coefficients for a rotor-journal bearing system based on equivalent load reconstruction , 2016 .

[27]  Igor Averbakh,et al.  On the complexity of minmax regret linear programming , 2005, Eur. J. Oper. Res..

[28]  Zhiping Qiu,et al.  Uncertainty analysis for heat convection-diffusion problem with large uncertain-but-bounded parameters , 2015 .

[29]  Mijia Yang,et al.  Impact location and load identification through inverse analysis with bounded uncertain measurements , 2013 .

[30]  H. Lee,et al.  Optimization of design parameters using a response surface method in a cold cross-wedge rolling , 2008 .

[31]  Jie Liu,et al.  A novel shape function approach of dynamic load identification for the structures with interval uncertainty , 2016 .

[32]  Singiresu S. Rao,et al.  Analysis of uncertain structural systems using interval analysis , 1997 .