Experimental Determination of Resultant Roll Force at Hot Plate Mill 5000

Abstract The paper deals with the methods to increase the accuracy of determination of roll torque on the motor shaft of the hot plate mill. Experiments are carried out by rolling of different steel grads eat the hot plate mill 5000. Thus, as a result of the carried out research it is obtained the experimental dependence to calculate angle of resultant roll force at hot plate mill, consequently it is possible to determine roll torque on the motor shaft of the rolling stand of the hot plate mill 5000 more accurately

[1]  Vadim R. Khramshin,et al.  Diagnostic Functions of a System for Continuous Monitoring of the Technical Condition of the Transformers of Arc Steelmaking Furnaces , 2014, Metallurgist.

[2]  Vadim Rifkhatovich Khramshin,et al.  Development and industrial introduction of systems for monitoring technical state of the rolling mills' electrical equipment , 2015, 2015 IEEE NW Russia Young Researchers in Electrical and Electronic Engineering Conference (EIConRusNW).

[3]  Olga Ivanovna Karandaeva,et al.  Metodology of calculation of the reliability indexes and life time of the electric and mechnical systems , 2014, 2014 International Conference on Mechanical Engineering, Automation and Control Systems (MEACS).

[4]  V. R. Gasiyarov,et al.  Smart Grid for main electric drive of plate mill rolling stand , 2014, 2014 International Conference on Mechanical Engineering, Automation and Control Systems (MEACS).

[5]  V. R. Gasiyarov,et al.  Research of electric drive at load impact on hot plate mill 5000 , 2015, 2015 International Conference on Mechanical Engineering, Automation and Control Systems (MEACS).

[6]  V. R. Gasiyarov,et al.  EMC analysis of 18-pulse AC-DC circuit consisting of three level AFE rectifiers based on PWMSHE method with three switching angles for quarter-period , 2016, 2016 IEEE NW Russia Young Researchers in Electrical and Electronic Engineering Conference (EIConRusNW).

[7]  Vadim R. Khramshin,et al.  Method for correction of gauge interference of the head-strip section in a system for automated controlling of the thickness of a broad-strip hot-rolling mill , 2013 .

[8]  V. R. Gasiyarov,et al.  Automatic Control System of Speed of Synchronous Motor , 2015 .

[9]  V. R. Gasiyarov,et al.  The Work Roll Bending Control System of the Hot Plate Rolling Mill , 2015 .

[10]  V. R. Gasiyarov,et al.  The Determination of Energy-power Parameters of Hot Plate Mill Mechatronic System , 2015 .

[11]  A. A. Radionov,et al.  Automatic gauge control system with combined control of the screw-down arrangement position , 2014, 2014 12th International Conference on Actual Problems of Electronics Instrument Engineering (APEIE).

[12]  V. R. Gasiyarov,et al.  Automatic gap control of Plan View Pattern Control Mechatronics System , 2015, 2015 International Siberian Conference on Control and Communications (SIBCON).

[13]  V. R. Gasiyarov,et al.  Modelling and Simulation of Three Level Inverters for Main Drive of the Plate Mill Rolling Stand , 2016 .

[14]  V. R. Gasiyarov,et al.  A development of the method of the control signal formation for the hot plate mill automation systems to improve the flatness of the finish plate , 2016 .

[15]  D. V. Korobatov,et al.  Effect of Different Winding Switching Methods on Regulating and Energetic Characteristics of Synchronous Motor with Permanent Magnet Excitation , 2015 .

[16]  G. P. Kornilov,et al.  System for speed mode control of the electric drives of the continuous train of the hot-rolling mill , 2015, 2015 International Siberian Conference on Control and Communications (SIBCON).

[17]  V. R. Gasiyarov,et al.  Improving Reliability of Hot Plate Mill Electromechanical System , 2016 .