Stepwise optimization of endplate of fuel cell stack assembled by steel belts

Abstract To reduce the mass and improve the uniformity of pressure distribution on the contact interfaces between the components of the proton exchange membrane fuel cell (PEMFC) stack clamped with steel belts, a multi-objective stepwise optimization method for the endplate is proposed in the present paper. We first divide the 2-D optimization problem into a two-step optimization, i.e. shape optimization and topology optimization, to improve the numerical convergence and stability. The simulated annealing method is introduced to promote the numerical efficiency and precision for the nonlinear contact optimization problem. Then the grid parameterization method is used, resulting in a smooth boundary topology optimization. Finally, based on the 2-D shape optimization and the improved topology optimization, a 3-D optimized topology is obtained using a geometry parameterization method. The final optimized endplate not only gives a small mass but also improves greatly the uniformity of the contact pressure distribution.

[1]  Wenying Chen.  Stepwise Optimal Design of Active Disturbances Rejection Vibration Controller for Intelligent Truss Structure Based on Adaptive Genetic Algorithm , 2010 .

[2]  Sung-hoon Ahn,et al.  Fuel Cell End Plates , 2008 .

[3]  Omar Z. Sharaf,et al.  An overview of fuel cell technology: Fundamentals and applications , 2014 .

[4]  Bin Lu,et al.  A direct shape optimization approach for contact problems with boundary stress concentration , 2013 .

[5]  Chengwei Wu,et al.  Mechanical Response of a Large Fuel Cell Stack to Impact: A Numerical Analysis , 2015 .

[6]  Luciano Lamberti,et al.  An efficient simulated annealing algorithm for design optimization of truss structures , 2008 .

[7]  Chai Wah Wu,et al.  Multi-objective topology optimization of end plates of proton exchange membrane fuel cell stacks , 2011 .

[8]  Dai Gil Lee,et al.  Composite endplates with pre-curvature for PEMFC (polymer electrolyte membrane fuel cell) , 2010 .

[9]  A. Kulikovsky.  A method for detection and location of current-free spots in a fuel cell stack: Numerical study , 2011 .

[10]  Ting-Yu Chen,et al.  Multiobjective optimal topology design of structures , 1998 .

[11]  A. Jarraya,et al.  Finite element implementation of an orthotropic plasticity model for sheet metal in low velocity impact simulations , 2015 .

[12]  O. Sigmund,et al.  Topology optimization approaches , 2013, Structural and Multidisciplinary Optimization.

[13]  N. Djilali,et al.  Effect of compression on liquid water transport and microstructure of PEMFC gas diffusion layers , 2007 .

[14]  Chengwei Wu,et al.  Contact resistance prediction and structure optimization of bipolar plates , 2006 .

[15]  M. R. Khorasani,et al.  Design and manufacturing of end plates of a 5 kW PEM fuel cell , 2010 .

[16]  Jamshid A. Samareh,et al.  Novel Multidisciplinary Shape Parameterization Approach , 2001 .

[17]  Min-Chie Chiu,et al.  Shape optimization of one‐chamber perforated plug/non‐plug mufflers by simulated annealing method , 2008 .

[18]  P. Lin,et al.  A high efficient assembly technique for large PEMFC stacks: Part I. Theory , 2009 .

[19]  Ren Yi-r.  CROSS SECTION DESIGN OF HELICOPTER ROTOR BLADE BASED ON TOPOLOGY OPTIMIZATION , 2014 .

[20]  Kailai Deng,et al.  Shape optimization design of steel shear panel dampers , 2014 .

[21]  Bi Zhang,et al.  Experimental study on clamping pressure distribution in PEM fuel cells , 2008 .

[22]  B. Yi,et al.  Research progress of aluminium alloy endplates for PEMFCs , 2007 .

[23]  Alex Bates,et al.  Simulation and experimental analysis of the clamping pressure distribution in a PEM fuel cell stack , 2013 .

[24]  Yun Wang,et al.  A review of polymer electrolyte membrane fuel cells: Technology, applications,and needs on fundamental research , 2011 .

[25]  Jun Ni,et al.  Robust design of assembly parameters on membrane electrode assembly pressure distribution , 2007 .