An experimental investigation and optimization of friction stir welding process for AA6082 T6 (cryogenic treated and untreated) using an integrated approach of Taguchi, grey relational analysis and entropy method

Friction stir welding is a solid state welding in which two metal parts are joined without melting with the help of frictional heat generated between the work material and non-consumable tool. Because of the poor microstructure, cracks, porosity and residual stresses in fusion welding of aircraft aluminium alloys, friction stir welding is highly attractive for joints in aircraft structures. In the present work, using Taguchi’s design of experiment method, combined effect of process parameters namely tool rotation speed, welding speed (or traverse speed of tool), tool pin profile and tool shoulder diameter have been investigated for the ultimate tensile strength and percentage elongation of friction stir welded joints of AA6082 alloy. Two similar sets of experiments were performed to prepare the friction stir welded joints; first samples of AA 6082-T6 (solution heat treated and artificially aged) were friction stir welded and second cryogenic treated AA6082 alloy were friction stir welded . A comparison in the optimal conditions of two sets of experiments has also been presented. In tempered aluminium alloy, three process parameters namely tool rotation, weld speed and tool shoulder diameter are significantly affecting ultimate tensile strength, while all four parameters are significant for percentage elongation. The influence of cryogenic treatment has also been noticed on two response characteristics. An integrated approach of Taguchi method, grey relational analysis and entropy measurement method have been utilized to obtain an optimal single setting of process parameters for two response characteristics. For the friction stir welded joint of AA6082-T6 (without cryogenic treatment), a single optimal setting of process parameters was obtained corresponding to tool rotation: 1200 r/min, weld speed: 35 mm/min, tool pin profile, threaded cylindrical and tool shoulder diameter: 16 mm. Similarly, the single optimal setting for cryogenic treated aluminium alloy (AA6082) was obtained corresponding to tool rotation: 1200 r/.min, weld speed: 35 mm/min, tool pin profile, cylindrical and tool shoulder diameter: 14 mm.

[1]  Rajiv S. Mishra,et al.  Friction Stir Welding and Processing , 2007 .

[2]  J. T. Chen,et al.  3D modeling of material flow in friction stir welding under different process parameters , 2007 .

[3]  J. Deng,et al.  Introduction to Grey system theory , 1989 .

[4]  R. Roy.  A Primer on the Taguchi Method , 1990 .

[5]  M. Sahin.  Joining of stainless-steel and aluminium materials by friction welding , 2009 .

[6]  L. Fratini,et al.  In-process heat treatments to improve FS-welded butt joints , 2009 .

[7]  Carla Gambaro,et al.  Friction stir welding of dissimilar Al 6013-T4 To X5CrNi18-10 stainless steel , 2005 .

[8]  V. Balasubramanian,et al.  Effect of welding processes on tensile properties of AA6061 aluminium alloy joints , 2009 .

[9]  U. Çaydas,et al.  Use of the grey relational analysis to determine optimum laser cutting parameters with multi-performance characteristics , 2008 .

[10]  V. Balasubramanian,et al.  An experimental investigation on friction stir welding of AZ31B magnesium alloy , 2010 .

[11]  Sandeep Grover,et al.  Simultaneous optimization of material removal rate and surface roughness for WEDM of WC-Co composite using grey relational analysis along with Taguchi method , 2011 .

[12]  Yifu Shen,et al.  Fabrication and anti-oxidation properties of Al/Ti-6Al-4V bimetallic clad-sheet by multi-pass friction stir welding , 2015 .

[13]  V. Balasubramanian,et al.  Influences of tool pin profile and axial force on the formation of friction stir processing zone in AA6061 aluminium alloy , 2008 .

[14]  K. Bhanumurthy,et al.  Friction Stir Welding of Al 5052 with Al 6061 Alloys , 2012 .

[15]  Mustafa Kemal Kulekci,et al.  Effects of tool rotation and pin diameter on fatigue properties of friction stir welded lap joints , 2008 .

[16]  Vinod Yadava,et al.  Diamond face grinding of WC-Co composite with spark assistance: Experimental study and parameter optimization , 2010 .

[17]  T Fukuda.  Friction stir welding (FSW) process , 2001 .

[18]  M. Stack.  Bridging the gap between tribology and corrosion: from wear maps to Pourbaix diagrams , 2005 .

[19]  Vinod Yadava,et al.  Multi-objective optimization of Nd:YAG laser cutting of thin superalloy sheet using grey relational analysis with entropy measurement , 2009 .

[20]  Z. Zhang,et al.  Material behaviors and mechanical features in friction stir welding process , 2007 .

[21]  J. T. Chen,et al.  Effect of shoulder size on the temperature rise and the material deformation in friction stir welding , 2009 .

[22]  Ulaş Çaydaş,et al.  Statistical analysis on mechanical properties of friction-stir-welded AA 1050/AA 5083 couples , 2009 .

[23]  V. Balasubramanian,et al.  Predictions of the optimized friction stir spot welding process parameters for joining AA2024 aluminum alloy using RSM , 2010 .

[24]  C. Muralidharan,et al.  Influence of friction stir welding process and tool parameters on strength properties of AA7075-T6 aluminium alloy joints , 2011 .

[25]  Richard Craig Van Nostrand,et al.  Design of Experiments Using the Taguchi Approach: 16 Steps to Product and Process Improvement , 2002, Technometrics.

[26]  M. Jahazi,et al.  Numerical analysis of the dwell phase in friction stir welding and comparison with experimental data , 2010 .

[27]  K.H.W. Seah,et al.  Performance evaluation of cryogenically treated tungsten carbide tools in turning , 2006 .

[28]  Linzhi Wu,et al.  Defects formation procedure and mathematic model for defect free friction stir welding of magnesium alloy , 2006 .

[29]  T. Sakthivel,et al.  Effect of welding speed on microstructure and mechanical properties of friction-stir-welded aluminum , 2009 .

[30]  N. C. Hwang,et al.  Grey relational analysis coupled with principal component analysis for optimization design of the cutting parameters in high-speed end milling , 2009 .

[31]  Hamed Pashazadeh,et al.  A study on material flow pattern in friction stir welding using finite element method , 2013 .

[32]  Sunil Pandey,et al.  Effect of process parameters on friction stir welding of aluminum alloy 2219-T87 , 2010 .

[33]  Yu-Min Chiang,et al.  The use of the Taguchi method with grey relational analysis to optimize the thin-film sputtering process with multiple quality characteristic in color filter manufacturing , 2009, Comput. Ind. Eng..

[34]  Mei-Li You,et al.  The grey entropy and its application in weighting analysis , 1998, SMC'98 Conference Proceedings. 1998 IEEE International Conference on Systems, Man, and Cybernetics (Cat. No.98CH36218).

[35]  Y. Gheisari,et al.  Weld defect formation in FSWed coppers , 2014, Journal of Materials Engineering and Performance.

[36]  Amit Sharma,et al.  Optimization of Cut Quality Characteristics during Nd:YAG Laser Straight Cutting of Ni-Based Superalloy Thin Sheet Using Grey Relational Analysis with Entropy Measurement , 2011 .