3D finite element model for predicting manufacturing distortions of composite parts

A 3D finite element model has been developed for predicting manufacturing distortions of fibre-reinforced thermosetting composite parts. The total curing process is divided into three steps that correspond to the states that resin passes through during curing: viscous, rubbery, and glassy. Tool–part interaction properties were calibrated by modelling the distortion of a single ply part. For comparison, composite parts of various geometries (L-section and U-section), stacking sequences, thicknesses, and bagging conditions were manufactured. The full field thickness profile and full field distortion pattern were obtained using a 3D laser scanner, which reveals higher and lower resin bleeding and corner thickening locations. The effect of stacking sequence is also examined with the full field distortion pattern. It was found that the parts manufactured under the bleeding condition give higher spring-in and warpage values. The spring-in predictions were well matched to measurements of the manufactured parts.

[1]  John W. Gillespie,et al.  Process-Induced Stress and Deformation in Thick-Section Thermoset Composite Laminates , 1992 .

[2]  Tonny Nyman,et al.  Prediction of Shape Distortions for a Curved Composite C-spar , 2005 .

[3]  Anoush Poursartip,et al.  Experimental and numerical study of the effect of cure cycle, tool surface, geometry, and lay-up on the dimensional fidelity of autoclave-processed composite parts , 2002 .

[4]  Reza Vaziri,et al.  A Plane Strain Model for Process-Induced Deformation of Laminated Composite Structures , 2001 .

[5]  J. Holmberg,et al.  An experimental investigation on mechanisms for manufacturing induced shape distortions in homogeneous and balanced laminates , 2001 .

[6]  J. Holmberg,et al.  Prediction of shape distortions. Part II. Experimental validation and analysis of boundary conditions , 2004 .

[7]  Qi Zhu,et al.  Dimensional Accuracy of Thermoset Composites: Simulation of Process-Induced Residual Stresses , 2001 .

[8]  Anoush Poursartip,et al.  Aspects of the Compaction of Composite Angle Laminates: An Experimental Investigation , 2001 .

[9]  Prediction of residual stresses and distortion in carbon fiber‐epoxy composite parts due to curing process using finite element analysis , 2013 .

[10]  Thomas Pardoen,et al.  Tooling geometry optimization for compensation of cure-induced distortions of a curved carbon/epoxy C-spar , 2014 .

[11]  Reza Vaziri,et al.  Closed-form solution for process-induced stresses and deformation of a composite part cured on a solid tool: Part II – Curved geometries , 2008 .

[12]  Nuri Ersoy,et al.  Modelling manufacturing deformations in corner sections made of composite materials , 2014 .

[13]  G. Springer,et al.  Curing of Epoxy Matrix Composites , 1983 .

[14]  T. Garstka,et al.  Separation of process induced distortions in curved composite laminates , 2005 .

[15]  Nuri Ersoy,et al.  Modelling of the spring-in phenomenon in curved parts made of a thermosetting composite , 2010 .

[16]  N. Ersoy,et al.  Effect of fibre wrinkling to the spring-in behaviour of L-shaped composite materials , 2015 .

[17]  Lloyd V. Smith,et al.  Isolating Components of Processing Induced Warpage in Laminated Composites , 2002 .

[18]  Nuri Ersoy,et al.  In situ measurements of through-the-thickness strains during processing of AS4/8552 composite , 2007 .

[19]  Nuri Ersoy,et al.  Mechanisms generating residual stresses and distortion during manufacture of polymer-matrix composite structures , 2006 .

[20]  C. Dong.  Modeling the process-induced dimensional variations of general curved composite components and assemblies , 2009 .

[21]  Véronique Michaud,et al.  Thermoviscoelastic anisotropic analysis of process induced residual stresses and dimensional stability in real polymer matrix composite components , 2006 .

[22]  Nuri Ersoy,et al.  Development of the properties of a carbon fibre reinforced thermosetting composite through cure , 2010 .

[23]  Scott R. White,et al.  Process Modeling of Composite Materials: Residual Stress Development during Cure. Part II. Experimental Validation , 1992 .

[24]  Scott R. White,et al.  Process Modeling of Composite Materials: Residual Stress Development during Cure. Part I. Model Formulation , 1992 .

[25]  Christian Hühne,et al.  A semi-analytical simulation strategy and its application to warpage of autoclave-processed CFRP parts , 2011 .

[26]  Anoush Poursartip,et al.  Tool -part interaction in composites processing. Part II: numerical modelling , 2004 .