Burning behavior of wood-plastic composite decking boards in end-use conditions: the effects of geometry, material composition, and moisture

In this study, we investigated the basic knowledge necessary to develop flame-retarded wood–plastic composite (WPC) materials by focusing on decking boards. Therefore, the respective effects of geometry, material composition, and moisture were studied by performing cone calorimetric measurements. Using hollow-shaped geometries removes combustible material and reduces the fire load but simultaneously increases fire propagation. The best results were achieved by using high-wood contents. The addition of talc can reduce the intensity of burning. Moisture also has a positive effect on burning behavior. Apart from the well-known mechanism of water, a change was observed in the resultant residue.

[1]  Robert H. White,et al.  Burning rate of solid wood measured in a heat release rate calorimeter , 1992 .

[2]  L. Broadbelt,et al.  Mechanistic modeling of polymer pyrolysis: Polypropylene , 2003 .

[3]  Colomba Di Blasi,et al.  Modeling chemical and physical processes of wood and biomass pyrolysis , 2008 .

[4]  R. B. Montgomery.  VISCOSITY AND THERMAL CONDUCTIVITY OF AIR AND DIFFUSIVITY OF WATER VAPOR IN AIR , 1947 .

[5]  T. Kitano,et al.  An empirical equation of the relative viscosity of polymer melts filled with various inorganic fillers , 1981 .

[6]  Robert H. White,et al.  EVALUATION OF VARIOUS FIRE RETARDANTS FOR USE IN WOOD FLOUR-POLYETHYLENE COMPOSITES , 2010 .

[7]  Olivier Beaumont,et al.  Influence of physical and chemical parameters on wood pyrolysis , 1984 .

[8]  Bernhard Schartel,et al.  Development of fire‐retarded materials—Interpretation of cone calorimeter data , 2007 .

[9]  J. Quintiere,et al.  Predicting the burning of wood using an integral model , 2000 .

[10]  D. Mohan,et al.  Pyrolysis of Wood/Biomass for Bio-oil: A Critical Review , 2006 .

[11]  F. H. Prager,et al.  Cone calorimetry—a review of tests carried out on plastics for the association of plastic manufacturers in Europe , 1991 .

[12]  Thomas A. Milne,et al.  Molecular characterization of the pyrolysis of biomass , 1987 .

[13]  Bernhard Schartel,et al.  Flame Retardant Mechanisms of Red Phosphorus and Magnesium Hydroxide in High Impact Polystyrene , 2004 .

[14]  T. Harada.  Time to ignition, heat release rate and fire endurance time of wood in cone calorimeter test , 2001 .

[15]  B. Schartel,et al.  Fire retardancy of polypropylene/flax blends , 2003 .

[16]  Mathew J. Hagge,et al.  Modeling the combined impact of moisture and char shrinkage on the pyrolysis of a biomass particle , 2003 .

[17]  L. Chia,et al.  A preliminary study on the thermal conductivity and flammability of WPC based on some tropical woods , 1985 .

[18]  Ondrej Grexa,et al.  Flammability parameters of wood tested on a cone calorimeter , 2001 .

[19]  S. Duquesne,et al.  Intumescent polypropylene/flax blends: a preliminary study , 2005 .

[20]  Richard H. Harris,et al.  Flammability Properties of Polymer - Layered-Silicate Nanocomposites. Polypropylene and Polystyrene Nanocomposites , 2000 .

[21]  Heinz Sturm,et al.  Flame retardancy mechanisms of metal phosphinates and metal phosphinates in combination with melamine cyanurate in glass‐fiber reinforced poly(1,4‐butylene terephthalate): the influence of metal cation , 2008 .

[22]  S. Bourbigot,et al.  Recent Advances for Intumescent Polymers , 2004 .