Espoused drum-buffer-rope flow control in serial lines: A comparative study of simulation models

This paper documents an investigation of drum-buffer-rope (DBR) scheduling and flow control methodology in single-product serial production lines. In particular, DBR flow control is reviewed and the importance of correctly representing this type of flow control mechanism in serial lines is discussed. Departures from valid DBR conceptual and simulation modeling are illustrated. It is shown that the model of a previously published paper is a push system not a DBR system, and that related conclusions regarding protective capacity and constraint location are unsupported. Correct modeling of DBR flow control is shown using discrete simulation experiments that compare the DBR model and a similar push model. Suggestions for additional research are offered.

[1]  Timothy D. Fry,et al.  Comparisons between drum–buffer–rope and material requirements planning: a case study , 2005 .

[2]  V. Daniel R. Guide,et al.  A Simulation Model of Drum-Buffer-Rope for Production Planning and Control at a Naval Aviation Depot , 1995, Simul..

[3]  D. R. Denzler,et al.  AN EXPERIMENTAL MODEL FOR INVESTIGATING THE SENSITIVITY OF JOB SHOP PERFORMANCE TO JOB RELEASE TIME DISTRIBUTION PARAMETERS , 2009 .

[4]  Jeff Cox,et al.  The Goal: A Process of Ongoing Improvement , 1984 .

[5]  Milan Gregor,et al.  FMS simulation: Some experience and recommendations , 1998, Simul. Pract. Theory.

[6]  John S. Morris,et al.  A simulation analysis of the effectiveness of drum-buffer-rope scheduling in furniture manufacturing , 1994 .

[7]  Eli Schragenheim,et al.  Manufacturing at warp speed : optimizing supply chain financial performance : includes simplified drum-buffer-rope , 2000 .

[8]  Jy Huang,et al.  Constructing procedures of an effective production activity control technique for a wafer fabrication environment , 1998 .

[9]  James F. Cox,et al.  Designing unbalanced lines - understanding protective capacity and protective inventory , 2002 .

[10]  V. J. Mabin,et al.  The World of the Theory of Constraints: A Review of the International Literature , 1999 .

[11]  John H. Blackstone,et al.  The evolution of a management philosophy: The theory of constraints , 2007 .

[12]  Jacob V. Simons,et al.  Simultaneous versus sequential scheduling of multiple resources which constrain system throughput , 1999 .

[13]  Phillip L. Carter,et al.  Shop floor control principles and practices and case studies , 1987 .

[14]  E. Goldratt.  The Haystack Syndrome: Sifting Information Out of the Data Ocean , 1990 .

[15]  Satya S. Chakravorty,et al.  A STUDY OF THE UTILIZATION OF CAPACITY CONSTRAINED RESOURCES IN DRUM‐BUFFER‐ROPE SYSTEMS* , 2009 .

[16]  Michael S. Spencer,et al.  The impact of a constraint buffer in a flow shop , 1995 .

[17]  Shigeru Fujimura,et al.  Buffer size setting method for DBR scheduling , 2007 .

[18]  William L. Maxwell,et al.  The Role of Work-in-Process Inventory in Serial Production Lines , 1988, Oper. Res..

[19]  Wendell G. Gilland.  A simulation study comparing performance of CONWIP and bottleneck-based release rules , 2002 .

[20]  V. Daniel,et al.  Scheduling with priority dispatching rules and drum-buffer-rope in a recoverable manufacturing system , 1997 .

[21]  Hokey Min,et al.  TOC-based performance measures and five focusing steps in a job-shop manufacturing environment , 2002 .

[22]  Timothy D. Fry,et al.  ORDER REVIEW/RELEASE AND LOT SPLITTING IN DRUM-BUFFER-ROPE , 1997 .

[23]  Basheer M. Khumawala,et al.  A study on the effect of the extent and location of protective capacity in flow systems , 2000 .

[24]  Satya S. Chakravorty,et al.  Does Protective Capacity Assist Managers in Competing Along Time-Based Dimensions? , 1994 .

[25]  Jeff Cox,et al.  The goal : excellence in manufacturing , 1984 .