Oil condition monitoring for HEMM – a case study

Purpose The paper aims to monitor the condition of heavy Earth-moving machines (HEMMs) used in open cast mines by lube oil analysis. Design/methodology/approach Oil samples at periodic interval were collected from the HEMM engine (Model No: BEML BH50M). Ferrography and Field Emission Scanning Electron Microscopy have been used for the wear particle analysis present in oil samples. Viscosity analysis and Fourier transform infrared spectroscopy have been done to investigate the degradation in quality and changes as compared to the initial structural properties of the lubricants. Findings The results obtained indicates wear in cylinder liner and piston ring. Copper, cast iron, alloy steel and ferrous oxide have been found as rubbing wear particles and cutting wear particles. Contamination level has also been found to be increasing in consecutive older oil samples. Chemical properties degraded with usage time and variations in oxidation and soot level have also been observed in every sample. Practical implications The results will be very much useful to maintenance teams of mining industry for early prediction of any impending failure of the machines, for example, diesel dilution, severe wear of the piston or cylinder liner leading to seizure can be predicted. Originality/value The HEMMs are an important piece of equipment in coal mining. Proper condition monitoring of HEMM is required to reduce the break down and down time to increase production.

[1]  T. Miyajima,et al.  Quantitative estimation of wear amounts by real time measurement of wear debris in lubricating oil , 2010 .

[2]  Thomas Brett Kirk,et al.  The development of three-dimensional imaging techniques of wear particle analysis , 1997 .

[3]  John J. Truhan,et al.  The effect of lubricating oil condition on the friction and wear of piston ring and cylinder liner materials in a reciprocating bench test , 2005 .

[4]  Xinping Yan,et al.  3D Surface Characterizations of Wear Particles Generated from Lubricated Regular Concave Cylinder Liners , 2014, Tribology Letters.

[5]  Manoj Kumar,et al.  Advancement and current status of wear debris analysis for machine condition monitoring: a review , 2013 .

[6]  Eui-Sung Yoon,et al.  Wear monitoring based on the analysis of lubricant contamination by optical ferroanalyzer , 2003 .

[7]  John H. Johnson,et al.  The development of Ferrography as a laboratory wear measurement method for the study of engine operating conditions on diesel engine wear , 1977 .

[8]  S. Raadnui,et al.  Wear particle analysis—utilization of quantitative computer image analysis: A review , 2005 .

[9]  Mridul Gautam,et al.  Effect of diesel soot on lubricant oil viscosity , 2007 .

[10]  Amitabh Jain,et al.  Evaluation of oil samples from centrifugal separators , 1993 .

[11]  M. Scherge,et al.  Characterization of wear debris of systems operated under low wear-rate conditions , 2006 .

[12]  V. M. Makarenko,et al.  On-line monitoring of the viscosity of lubricating oils , 2010 .

[13]  Bernardo Tormos,et al.  Applying analytical ferrography as a technique to detect failures in Diesel engine fuel injection systems , 2006 .

[14]  Pawel Podsiadlo,et al.  Automated classification of wear particles based on their surface texture and shape features , 2008 .

[15]  T. B. Kirk,et al.  Computer image analysis of wear particles in three-dimensions for machine condition monitoring , 1998 .

[16]  S. K. Basu,et al.  Vibration and Oil Analysis by Ferrography for Condition Monitoring , 2013 .

[17]  Zhongxiao Peng,et al.  A study of the effect of contaminant particles in lubricants using wear debris and vibration condition monitoring techniques , 2005 .

[18]  Anand Prabhakaran,et al.  Condition monitoring of steam turbine-generator through contamination analysis of used lubricating oil , 1999 .