International Journal of Renewable Energy Development

Since the early years of the 21st century, the whole world has faced two very urgent problems: the depletion of fossil energy sources and climate change due to environmental pollution. Among the solutions sought, 2,5-Dimethylfuran (DMF) emerged as a promising solution. DMF is a 2nd generation biofuel capable of mass production from biomass. There have been many studies confirming that DMF is a potential alternative fuel for traditional fuels (gasoline and diesel) in internal combustion engines, contributing to solving the problem of energy security and environmental pollution. However, in order to apply DMF in practice, more comprehensive studies are needed. Not out of the above trend, this paper analyzes and discusses in detail the characteristics of DMF's combustible laminar flame and its instability under different initial conditions. The evaluation results show that the flame characteristics of DMF are similar to those of gasoline, although the burning rate of DMF is much higher than that of gasoline. This shows that DMF can become a potential alternative fuel in internal combustion engines.

[1]  R. Luque,et al.  Catalyst-Based Synthesis of 2,5-Dimethylfuran from Carbohydrates as a Sustainable Biofuel Production Route , 2022, ACS Sustainable Chemistry & Engineering.

[2]  Yong Jiang,et al.  Effects of diluents on laminar burning velocity and cellular instability of 2-methyltetrahydrofuran-air flames , 2022, Fuel.

[3]  Sudarshan Kumar,et al.  Formulation of a three-component gasoline surrogate model using laminar burning velocity data at elevated mixture temperatures , 2021 .

[4]  Hwai Chyuan Ong,et al.  Characteristics of hydrogen production from steam gasification of plant-originated lignocellulosic biomass and its prospects in Vietnam , 2021, International Journal of Hydrogen Energy.

[5]  A. Hoang,et al.  Hydrogen-Enriched Biogas Premixed Charge Combustion and Emissions in Direct Injection and Indirect Injection Diesel Dual Fueled Engines: A Comparative Study , 2021, Journal of Energy Resources Technology.

[6]  Hwai Chyuan Ong,et al.  Progress on the lignocellulosic biomass pyrolysis for biofuel production toward environmental sustainability , 2021 .

[7]  Thanh H. Truong,et al.  Laminar Flame Characteristics of 2,5-Dimethylfuran (DMF) Biofuel: A Comparative Review with Ethanol and Gasoline , 2021, International Journal of Renewable Energy Development.

[8]  P. Manage,et al.  Isolation and Identification of Cellulase Producing and Sugar Fermenting Bacteria for Second-Generation Bioethanol Production , 2021 .

[9]  A. Hoang,et al.  Influence of Various Basin Types on Performance of Passive Solar Still: A Review , 2021 .

[10]  A. Hoang,et al.  Integrated biorefineries, circular bio-economy, and valorization of organic waste streams with respect to bio-products , 2021, Biomass Conversion and Biorefinery.

[11]  Nikhil S. Kadam,et al.  Investigation on seed oil chemistry of Bauhinia racemosa for the production of liquid biofuel , 2021, Energy Sources, Part A: Recovery, Utilization, and Environmental Effects.

[12]  N. S. Amin,et al.  Recent advances in green pre-treatment methods of lignocellulosic biomass for enhanced biofuel production , 2021, Journal of Cleaner Production.

[13]  H. Pitsch,et al.  Exploring the fuel structure dependence of laminar burning velocity: A machine learning based group contribution approach , 2021 .

[14]  R. Luque,et al.  Liquid hot water as sustainable biomass pretreatment technique for bioenergy production: A review. , 2021, Bioresource technology.

[15]  Hu Li,et al.  One-pot domino conversion of biomass-derived furfural to γ-valerolactone with an in-situ formed bifunctional catalyst , 2021, Energy Sources, Part A: Recovery, Utilization, and Environmental Effects.

[16]  Jai Gopal Gupta,et al.  Engine durability and lubricating oil tribology study of a biodiesel fuelled common rail direct injection medium-duty transportation diesel engine , 2021, Wear.

[17]  A. Pugazhendhi,et al.  CO2 reduction in a common rail direct injection engine using the combined effect of low carbon biofuels, hydrogen and a post combustion carbon capture system , 2021, Energy Sources, Part A: Recovery, Utilization, and Environmental Effects.

[18]  A. Hoang,et al.  Role of hydrogen in improving performance and emission characteristics of homogeneous charge compression ignition engine fueled with graphite oxide nanoparticle-added microalgae biodiesel/diesel blends , 2021, International Journal of Hydrogen Energy.

[19]  A. Hoang,et al.  2-Methylfuran (MF) as a potential biofuel: A thorough review on the production pathway from biomass, combustion progress, and application in engines , 2021 .

[20]  V. H. Dong,et al.  Mission, challenges, and prospects of renewable energy development in Vietnam , 2021, Energy Sources, Part A: Recovery, Utilization, and Environmental Effects.

[21]  E. Varuvel,et al.  Experimental evaluation of a compression ignition engine enacted with biofuel from beverage industry waste and higher grades of alcohol , 2021, Energy Sources, Part A: Recovery, Utilization, and Environmental Effects.

[22]  M. Aschi,et al.  Theoretical and experimental study on the O(3P) + 2,5-dimethylfuran reaction in the gas phase. , 2021, Physical chemistry chemical physics : PCCP.

[23]  K. Nanthagopal,et al.  Investigations on compression ignition engine durability through long-term endurance study using low viscous biofuel blends , 2021, Clean Technologies and Environmental Policy.

[24]  A. Hoang,et al.  Application of the Internet of Things in 3E (efficiency, economy, and environment) factor-based energy management as smart and sustainable strategy , 2021, Energy Sources, Part A: Recovery, Utilization, and Environmental Effects.

[25]  J. Klemeš,et al.  COVID-19 pandemics Stage II – Energy and environmental impacts of vaccination , 2021, Renewable and Sustainable Energy Reviews.

[26]  Hwai Chyuan Ong,et al.  Acid-based lignocellulosic biomass biorefinery for bioenergy production: Advantages, application constraints, and perspectives. , 2021, Journal of environmental management.

[27]  A. Hoang Combustion behavior, performance and emission characteristics of diesel engine fuelled with biodiesel containing cerium oxide nanoparticles: A review , 2021, Fuel Processing Technology.

[28]  S. Uslu,et al.  Impact of a novel fuel additive containing boron and hydrogen on diesel engine performance and emissions , 2021, Energy Sources, Part A: Recovery, Utilization, and Environmental Effects.

[29]  A. Alami,et al.  Cultivation of Nannochloropsis algae for simultaneous biomass applications and carbon dioxide capture , 2021 .

[30]  Yuqiang Li,et al.  Development and application of a practical diesel-n-butanol-PAH mechanism in engine combustion and emissions prediction , 2021 .

[31]  Ş. Altun,et al.  Effect of biodiesel addition in a blend of isopropanol-butanol-ethanol and diesel on combustion and emissions of a CRDI engine , 2021, Energy Sources, Part A: Recovery, Utilization, and Environmental Effects.

[32]  Hwai Chyuan Ong,et al.  Insight into the recent advances of microwave pretreatment technologies for the conversion of lignocellulosic biomass into sustainable biofuel. , 2021, Chemosphere.

[33]  Hadiyanto Hadiyanto,et al.  Potential for Environmental Services Based on the Estimation of Reserved Carbon in the Mangunharjo Mangrove Ecosystem , 2021 .

[34]  S. Wahyuni,et al.  Esterification of Bio-Oil Produced from Sengon (Paraserianthes falcataria) Wood Using Indonesian Natural Zeolites , 2021, International Journal of Renewable Energy Development.

[35]  A. Hoang,et al.  Smart control strategy for effective hydrocarbon and carbon monoxide emission reduction on a conventional diesel engine using the pooled impact of pre-and post-combustion techniques , 2021, Journal of Cleaner Production.

[36]  Hwai Chyuan Ong,et al.  Impacts of COVID-19 pandemic on the global energy system and the shift progress to renewable energy: Opportunities, challenges, and policy implications , 2021, Energy Policy.

[37]  A. Hoang,et al.  Integrating renewable sources into energy system for smart city as a sagacious strategy towards clean and sustainable process , 2021, Journal of Cleaner Production.

[38]  A. Hoang,et al.  Biomass-derived 2,5-dimethylfuran as a promising alternative fuel: An application review on the compression and spark ignition engine , 2021 .

[39]  A. Hoang,et al.  COVID-19 and the Global Shift Progress to Clean Energy , 2021 .

[40]  A. Hoang,et al.  A Review on the Performance, Combustion, and Emission Characteristics of Spark-Ignition Engine Fueled With 2,5-Dimethylfuran Compared to Ethanol and Gasoline , 2021 .

[41]  A. Hoang,et al.  Use of Biodiesel Fuels in Diesel Engines , 2021, Biodiesel Fuels.

[42]  Hwai Chyuan Ong,et al.  Synthesis pathway and combustion mechanism of a sustainable biofuel 2,5-Dimethylfuran: Progress and prospective , 2021 .

[43]  A. Hoang,et al.  2,5-Dimethylfuran (DMF) as a promising biofuel for the spark ignition engine application: A comparative analysis and review , 2021 .

[44]  A. Hoang,et al.  Record decline in global CO2 emissions prompted by COVID-19 pandemic and its implications on future climate change policies , 2021 .

[45]  Y. Ju,et al.  Experimental Investigation and Optimization of Non-Catalytic In-Situ Biodiesel Production from Rice Bran Using with RSM Historical Data Design , 2021 .

[46]  Trung Thanh Bui,et al.  Characteristics of PM and soot emissions of internal combustion engines running on biomass-derived DMF biofuel: a review , 2020, Energy Sources, Part A: Recovery, Utilization, and Environmental Effects.

[47]  Trung Thanh Bui,et al.  A review on ignition delay times of 2,5-Dimethylfuran , 2020, Energy Sources, Part A: Recovery, Utilization, and Environmental Effects.

[48]  Y. Rilda,et al.  Synthesis of Graphene Oxide Enriched Natural Kaolinite Clay and Its Application For Biodiesel Production , 2020, International Journal of Renewable Energy Development.

[49]  Seema Singh,et al.  Transforming lignocellulosic biomass into biofuels enabled by ionic liquid pretreatment. , 2020, Bioresource technology.

[50]  Baoxiang Peng,et al.  Formic Acid‐Assisted Selective Hydrogenolysis of 5‐Hydroxymethylfurfural to 2,5‐Dimethylfuran over Bifunctional Pd Nanoparticles Supported on N‐Doped Mesoporous Carbon , 2020, Angewandte Chemie.

[51]  A. Hoang,et al.  A remarkable review of the effect of lockdowns during COVID-19 pandemic on global PM emissions , 2020 .

[52]  A. Hoang,et al.  A review of the effect of biodiesel on the corrosion behavior of metals/alloys in diesel engines , 2020, Energy Sources, Part A: Recovery, Utilization, and Environmental Effects.

[53]  A. Le,et al.  Combustion and emission characteristics of spark and compression ignition engine fueled with 2,5-dimethylfuran (DMF): A comprehensive review , 2020, Fuel.

[54]  A. Hoang,et al.  A state-of-the-art review on emission characteristics of SI and CI engines fueled with 2,5-dimethylfuran biofuel , 2020, Environmental Science and Pollution Research.

[55]  Mohammad Hossein Nadian,et al.  Soft computing-based modeling and emission control/reduction of a diesel engine fueled with carbon nanoparticle-dosed water/diesel ‎emulsion fuel. , 2020, Journal of hazardous materials.

[56]  N. Bharadvaja,et al.  A review on microalgae biofuel and biorefinery: challenges and way forward , 2020 .

[57]  B. Ashok,et al.  Multi-functional fuel additive as a combustion catalyst for diesel and biodiesel in CI engine characteristics , 2020, Fuel.

[58]  A. Hoang,et al.  Prospective review on the application of biofuel 2,5-dimethylfuran to diesel engine , 2020 .

[59]  A. Hoang,et al.  Flame Characteristics and Ignition Delay Times of 2,5-Dimethylfuran: A Systematic Review With Comparative Analysis , 2020 .

[60]  Feiyue Wang CO2_reduction , 2020, ioChem-BD Computational Chemistry Datasets.

[61]  Qi Huang,et al.  A biomass-integrated comprehensive energy system: thermodynamics assessment and performance comparison of sugarcane bagasse and rice husk as input source , 2020 .

[62]  T. Wu,et al.  An application of ultrasonication in lignocellulosic biomass valorisation into bio-energy and bio-based products , 2020 .

[63]  H. Ghazali,et al.  Bioethanol production from Brewer’s rice by Saccharomyces cerevisiae and Zymomonas mobilis: evaluation of process kinetics and performance , 2020 .

[64]  Renganathan Sahadevan,et al.  An innovative plasma pre-treatment process for lignocellulosic bio-ethanol production , 2020 .

[65]  M. Jędrzejczyk,et al.  Highly Efficient Production of DMF from Biomass-Derived HMF on Recyclable Ni-Fe/TiO2 Catalysts , 2020 .

[66]  Yong Jiang,et al.  Laminar burning velocities of 2-methyltetrahydrofuran at elevated pressures , 2020 .

[67]  H. Chu,et al.  Effects of 2, 5–dimethylfuran/ethanol addition on soot formation in n-heptane/iso-octane/air coflow diffusion flames , 2020 .

[68]  Wenguang Zhao,et al.  Selective hydrogenolysis of 5-hydroxymethylfurfural to produce biofuel 2, 5-dimethylfuran over Ni/ZSM-5 catalysts , 2020, Fuel.

[69]  A. Saraeyan,et al.  Improving technical parameters of biofuel briquettes using cellulosic binders , 2020 .

[70]  Sudeepta Pradhan,et al.  Present and future impact of COVID-19 in the renewable energy sector: a case study on India , 2020 .

[71]  A. Hoang,et al.  Performance and combustion characteristics of a retrofitted CNG engine under various piston-top shapes and compression ratios , 2020, Energy Sources, Part A: Recovery, Utilization, and Environmental Effects.

[72]  D. Anggoro,et al.  GLYCEROLYSIS USING KF/CAO-MGO CATALYST: OPTIMISATION AND REACTION KINETICS , 2020 .

[73]  A. Hoang,et al.  A simulation study on a port-injection SI engine fueled with hydroxy-enriched biogas , 2020 .

[74]  Hadiyanto Hadiyanto,et al.  Performance evaluation of yeast-assisted microalgal microbial fuel cells on bioremediation of cafeteria wastewater for electricity generation and microalgae biomass production , 2020 .

[75]  Ryan P. Lively,et al.  Separation and Purification of 2,5-Dimethylfuran: Process Design and Comparative Technoeconomic and Sustainability Evaluation of Simulated Moving Bed Adsorption and Conventional Distillation , 2020 .

[76]  N. Tippayawong,et al.  Generating Organic Liquid Products from Catalytic Cracking of Used Cooking Oil over Mechanically Mixed Catalysts , 2020 .

[77]  Yuqi Wang,et al.  Selective hydrogenolysis of 5-hydroxymethylfurfural to 2,5-dimethylfuran catalyzed by ordered mesoporous alumina supported nickel-molybdenum sulfide catalysts , 2020 .

[78]  Mohammad Amin Sobati,et al.  Regeneration of different extractive solvents for the oxidative desulfurization process: An experimental investigation , 2020 .

[79]  Xuhao Li,et al.  Catalytic hydrogenation of 5-hydroxymethylfurfural to 2,5-dimethylfuran over Ru based catalyst: Effects of process parameters on conversion and products selectivity , 2020 .

[80]  M. Budihardjo,et al.  Assessing the Environmental Performance of Palm Oil Biodiesel Production in Indonesia: A Life Cycle Assessment Approach , 2020, Energies.

[81]  K. Alexandrino Comprehensive Review of the Impact of 2,5-Dimethylfuran and 2-Methylfuran on Soot Emissions: Experiments in Diesel Engines and at Laboratory-Scale , 2020 .

[82]  J. E,et al.  Laminar burning velocity and pollutant emissions of the gasoline components and its surrogate fuels: A review , 2020 .

[83]  Shiye Wang,et al.  Effect of Engine Speeds and Dimethyl Ether on Methyl Decanoate HCCI Combustion and Emission Characteristics Based on Low-Speed Two-Stroke Diesel Engine , 2020, Polish Maritime Research.

[84]  A. Hoang,et al.  A study on a solution to reduce emissions by using hydrogen as an alternative fuel for a diesel engine integrated exhaust gas recirculation , 2020 .

[85]  Dao Nam Cao,et al.  Effects of injection pressure on the NOx and PM emission control of diesel engine: A review under the aspect of PCCI combustion condition , 2020 .

[86]  Manuel Romero Gómez,et al.  Generation of H2 on Board Lng Vessels for Consumption in the Propulsion System , 2020, Polish Maritime Research.

[87]  A. Hoang Applicability of fuel injection techniques for modern diesel engines , 2020 .

[88]  T. Su,et al.  Catalytic hydrogenolysis of hydroxymethylfurfural to highly selective 2,5-dimethylfuran over FeCoNi/h-BN catalyst , 2020 .

[89]  Mingfei Chen,et al.  Nanostructure and reactivity of soot from biofuel 2,5-dimethylfuran pyrolysis with CO2 additions , 2020, Frontiers in Energy.

[90]  R. Ravikrishna,et al.  Experiments and Kinetic Modeling of Diffusion Flame Extinction of 2-Methylfuran, 2,5-Dimethylfuran, and Binary Mixtures with Isooctane , 2020 .

[91]  A. Hoang,et al.  Technological Perspective for Reducing Emissions from Marine Engines , 2019 .

[92]  C. M. Piekarski,et al.  Sustainability of sugarcane lignocellulosic biomass pretreatment for the production of bioethanol. , 2019, Bioresource technology.

[93]  Changzhao Jiang,et al.  Effect of CO2 and N2 dilution on laminar premixed MTHF/air flames: Experiments and kinetic studies , 2019, Fuel.

[94]  A. Nikkhah,et al.  Sustainable second-generation biofuel production potential in a developing country case study , 2019, Energy Sources, Part A: Recovery, Utilization, and Environmental Effects.

[95]  Longlong Ma,et al.  Selective Hydrodeoxygenation of 5-Hydroxymethylfurfural to 2,5-Dimethylfuran over Alloyed Cu−Ni Encapsulated in Biochar Catalysts , 2019, ACS Sustainable Chemistry & Engineering.

[96]  Jinghua Li,et al.  A reduced mechanism for 2,5-dimetylfuran with assembled mechanism reduction methods , 2019, Fuel.

[97]  R. Luque,et al.  Continuous Flow Selective Hydrogenation of 5-Hydroxymethylfurfural to 2,5-Dimethylfuran Using Highly Active and Stable Cu–Pd/Reduced Graphene Oxide , 2019, ACS Sustainable Chemistry & Engineering.

[98]  Yongliang Xie,et al.  Effect of the initial pressures on evolution of intrinsically unstable hydrogen/air premixed flame fronts , 2019, International Journal of Hydrogen Energy.

[99]  A. Hoang,et al.  A core correlation of spray characteristics, deposit formation, and combustion of a high-speed diesel engine fueled with Jatropha oil and diesel fuel , 2019, Fuel.

[100]  Yong Yang,et al.  Investigation on Blending Effects of Gasoline Fuel with N-Butanol, DMF, and Ethanol on the Fuel Consumption and Harmful Emissions in a GDI Vehicle , 2019, Energies.

[101]  Xinhua Liang,et al.  Catalytic hydrogenolysis of biomass-derived 5-hydroxymethylfurfural to biofuel 2, 5-dimethylfuran , 2019, Applied Catalysis A: General.

[102]  V. H. Dong,et al.  An experimental analysis on physical properties and spray characteristics of an ultrasound-assisted emulsion of ultra-low-sulphur diesel and Jatropha-based biodiesel , 2019, Journal of Marine Engineering & Technology.

[103]  L. Qin,et al.  A non-noble bimetallic alloy in the highly selective electrochemical synthesis of the biofuel 2,5-dimethylfuran from 5-hydroxymethylfurfural , 2019, Green Chemistry.

[104]  A. Hoang,et al.  Trilateral correlation of spray characteristics, combustion parameters, and deposit formation in the injector hole of a diesel engine running on preheated Jatropha oil and fossil diesel fuel , 2019, Biofuel Research Journal.

[105]  A. Hoang,et al.  An investigation of deposit formation in the injector, spray characteristics, and performance of a diesel engine fueled with preheated vegetable oil and diesel fuel , 2019, Energy Sources, Part A: Recovery, Utilization, and Environmental Effects.

[106]  A. Hoang,et al.  Experimental Analysis on the Ultrasound-based Mixing Technique Applied to Ultra-low Sulphur Diesel and Bio-oils , 2019, International Journal on Advanced Science, Engineering and Information Technology.

[107]  M. M. Noor,et al.  A review of the performance and emissions of nano additives in diesel fuelled compression ignition-engines , 2019, IOP Conference Series: Materials Science and Engineering.

[108]  A. Hoang,et al.  Properties of DMF-fossil gasoline RON95 blends in the consideration as the alternative fuel , 2018, International Journal on Advanced Science, Engineering and Information Technology.

[109]  A. Hoang,et al.  Influences of heating temperatures on physical properties, spray characteristics of bio-oils and fuel supply system of a conventional diesel engine , 2018, International Journal on Advanced Science, Engineering and Information Technology.

[110]  A. Hoang Prediction of the density and viscosity of biodiesel and the influence of biodiesel properties on a diesel engine fuel supply system , 2018, Journal of Marine Engineering & Technology.

[111]  Minh Tuan Pham,et al.  Measurement and Prediction of the Density and Viscosity of Biodiesel Blends , 2018, International Journal of Technology.

[112]  Shrabanti Roy,et al.  Understanding the Effect of Oxygenated Additives on Combustion Characteristics of Gasoline , 2018, Journal of Energy Resources Technology.

[113]  A. Hoang,et al.  A study of emission characteristic, deposits, and lubrication oil degradation of a diesel engine running on preheated vegetable oil and diesel oil , 2018, Energy Sources, Part A: Recovery, Utilization, and Environmental Effects.

[114]  Sudarshan Kumar,et al.  A comprehensive review of measurements and data analysis of laminar burning velocities for various fuel+air mixtures , 2018, Progress in Energy and Combustion Science.

[115]  A. Datta,et al.  Effects of blending 2,5-dimethylfuran on the laminar burning velocity and ignition delay time of isooctane/air mixture , 2018, Combustion Theory and Modelling.

[116]  A. Raj,et al.  On the characteristics and reactivity of soot particles from ethanol-gasoline and 2,5-dimethylfuran-gasoline blends , 2018, Fuel.

[117]  A. Hoang,et al.  Comparative analysis on performance and emission characteristic of diesel engine fueled with heated coconut oil and diesel fuel , 2018 .

[118]  P. Zhang,et al.  Laser diagnostics and chemical kinetic analysis of PAHs and soot in co-flow partially premixed flames using diesel surrogate and oxygenated additives of n-butanol and DMF , 2018 .

[119]  P. C. Mishra,et al.  Analysis of a diesel engine fuelled with jojoba blend and coir pith producer gas , 2017 .

[120]  Mingrui Wei,et al.  Effects of injection timing on combustion and emissions in a diesel engine fueled with 2,5-dimethylfuran-diesel blends , 2017 .

[121]  Tuan Anh Hoang,et al.  The Performance of a Diesel Engine Fueled with Diesel Oil, Biodiesel and Preheated Coconut Oil , 2017 .

[122]  S. K. Nayak,et al.  Functional characteristics of jatropha biodiesel as a promising feedstock for engine application , 2017 .

[123]  Hongming Xu,et al.  Laminar burning characteristics of ethyl propionate, ethyl butyrate, ethyl acetate, gasoline and ethanol fuels , 2016 .

[124]  P. C. Mishra,et al.  Emission from utilization of producer gas and mixes of jatropha biodiesel , 2016 .

[125]  Zuo-hua Huang,et al.  Review on the production methods and fundamental combustion characteristics of furan derivatives , 2016 .

[126]  Norma E. Conner,et al.  Advances and Challenges , 2016, The American journal of hospice & palliative care.

[127]  Jinyue Yan,et al.  Oxy-fuel combustion of pulverized fuels: Combustion fundamentals and modeling , 2016 .

[128]  B. Saha,et al.  Upgrading Furfurals to Drop-in Biofuels: An Overview , 2015 .

[129]  A. Tomboulides,et al.  Consistent definitions of “Flame Displacement Speed” and “Markstein Length” for premixed flame propagation , 2015 .

[130]  K. Ebitani,et al.  Selective hydrogenation of biomass-derived 5-hydroxymethylfurfural (HMF) to 2,5-dimethylfuran (DMF) under atmospheric hydrogen pressure over carbon supported PdAu bimetallic catalyst , 2014 .

[131]  F. Egolfopoulos,et al.  Advances and challenges in laminar flame experiments and implications for combustion chemistry , 2014 .

[132]  I. Wardana,et al.  Premixed Combustion of Kapok (ceiba pentandra) seed oil on Perforated Burner , 2014 .

[133]  Shijin Shuai,et al.  Ultra-high speed imaging and OH-LIF study of DMF and MF combustion in a DISI optical engine , 2014 .

[134]  F. Gillespie An experimental and modelling study of the combustion of oxygenated hydrocarbons , 2014 .

[135]  Xiao-hui Liu,et al.  Efficient production of the liquid fuel 2,5-dimethylfuran from 5-hydroxymethylfurfural over Ru/Co3O4 catalyst , 2014 .

[136]  Zuo-hua Huang,et al.  Progress in combustion investigations of hydrogen enriched hydrocarbons , 2014 .

[137]  Changzhao Jiang,et al.  Laminar burning characteristics of 2-methylfuran and isooctane blend fuels , 2014 .

[138]  P. Glaude,et al.  A comprehensive experimental and detailed chemical kinetic modelling study of 2,5-dimethylfuran pyrolysis and oxidation. , 2013, Combustion and flame.

[139]  Changzhao Jiang,et al.  Laminar Burning Characteristics of 2-Methylfuran Compared with 2,5-Dimethylfuran and Isooctane , 2013 .

[140]  Mingfa Yao,et al.  Experimental study on combustion and emission characteristics of a diesel engine fueled with 2,5-dimethylfuran–diesel, n-butanol–diesel and gasoline–diesel blends , 2013 .

[141]  A. Maghbouli,et al.  Detailed physical properties prediction of pure methyl esters for biodiesel combustion modeling , 2013 .

[142]  S. Dutta Deoxygenation of biomass-derived feedstocks: hurdles and opportunities. , 2012, ChemSusChem.

[143]  F. Halter,et al.  Effects of high pressure, high temperature and dilution on laminar burning velocities and Markstein lengths of iso-octane/air mixtures , 2012 .

[144]  Hongming Xu,et al.  Speciation of hydrocarbon and carbonyl emissions of 2,5-dimethylfuran combustion in a DISI engine , 2012 .

[145]  Zuo-hua Huang,et al.  Laminar burning characteristics of 2,5-dimethylfuran and iso-octane blend at elevated temperatures and pressures , 2012 .

[146]  Guohong Tian,et al.  Split-Injection Strategies under Full-Load Using DMF, A New Biofuel Candidate, Compared to Ethanol in a GDI Engine , 2012 .

[147]  Md. Imteyaz Alam,et al.  Direct conversion of cellulose and lignocellulosic biomass into chemicals and biofuel with metal chloride catalysts , 2012 .

[148]  Zuo-hua Huang,et al.  Laminar Flame Speeds of DMF/Iso-octane-Air-N2/CO2 Mixtures , 2012 .

[149]  Blanca Estela García-Flores,et al.  Prediction of the density and viscosity in biodiesel blends at various temperatures , 2011 .

[150]  Zuo-hua Huang,et al.  Laminar burning velocities and flame instabilities of 2,5-dimethylfuran–air mixtures at elevated pressures , 2011 .

[151]  Zuo-hua Huang,et al.  Laminar Burning Velocities and Markstein Lengths of 2,5-Dimethylfuran-Air Premixed Flames at Elevated Temperatures , 2010 .

[152]  Alexis T. Bell,et al.  A two-step approach for the catalytic conversion of glucose to 2,5-dimethylfuran in ionic liquids , 2010 .

[153]  Hongming Xu,et al.  Laminar Burning Velocities of 2,5-Dimethylfuran Compared with Ethanol and Gasoline , 2010 .

[154]  Zuo-hua Huang,et al.  Measurements of Laminar Burning Velocities and Markstein Lengths of 2,5-Dimethylfuran−Air−Diluent Premixed Flames , 2009 .

[155]  M. P. Burke,et al.  Effect of cylindrical confinement on the determination of laminar flame speeds using outwardly propagating flames , 2009 .

[156]  Ronald T. Raines,et al.  Simple chemical transformation of lignocellulosic biomass into furans for fuels and chemicals. , 2009, Journal of the American Chemical Society.

[157]  C. Law,et al.  On transition to cellularity in expanding spherical flames , 2007, Journal of Fluid Mechanics.

[158]  Yuriy Román‐Leshkov,et al.  Production of dimethylfuran for liquid fuels from biomass-derived carbohydrates , 2007, Nature.

[159]  Sebastian Verhelst,et al.  Laminar burning velocities of lean hydrogen-air mixtures at pressures up to 1.0 MPa , 2007 .

[160]  Zuo-hua Huang,et al.  Measurements of laminar burning velocities for natural gas–hydrogen–air mixtures , 2006 .

[161]  Atsushi Teraji,et al.  Development of a Novel Flame Propagation Model (UCFM: Universal Coherent Flamelet Model) for SI Engines and Its Application to Knocking Prediction , 2005 .

[162]  A. Lifshitz,et al.  Thermal Decomposition of 2,5-Dimethylfuran. Experimental Results and Computer Modeling , 1998 .

[163]  Tony Travers,et al.  A Comprehensive Review , 1998 .

[164]  P. Carlsson,et al.  Valorisation of 2,5-dimethylfuran over zeolite catalysts studied by on-line FTIR-MS gas phase analysis , 2021, Catalysis science & technology.

[165]  D. Rodríguez,et al.  Secondary organic aerosol formation from the ozonolysis and oh-photooxidation of 2,5-dimethylfuran , 2021, Atmospheric Environment.

[166]  A. Ghassemi,et al.  Rice bran oil-based biodiesel as a promising renewable fuel alternative to petrodiesel: A review , 2021 .

[167]  O. Harireche,et al.  The Potential of Wind Energy and Design Implications on Wind Farms in Saudi Arabia , 2021 .

[168]  A. Hoang,et al.  A simulation research of heat transfers and chemical reactions in the fuel steam reformer using exhaust gas energy from motorcycle engine , 2020 .

[169]  F. Spellman Combustion Theory , 2020 .

[170]  A. Hoang,et al.  Performance and Emission Characteristics of Popular 4-Stroke Motorcycle Engine in Vietnam Fuelled with Biogasoline Compared with Fossil Gasoline , 2018 .

[171]  A. Hoang Emission Characteristics of a Diesel Engine Fuelled with Preheated Vegetable Oil and Biodiesel , 2017 .

[172]  Dong Liu,et al.  Combustion chemistry and flame structure of furan group biofuels using molecular-beam mass spectrometry and gas chromatography - Part I: Furan. , 2014, Combustion and flame.

[173]  Pierre-Alexandre Glaude,et al.  Combustion chemistry and flame structure of furan group biofuels using molecular-beam mass spectrometry and gas chromatography - Part III: 2,5-Dimethylfuran. , 2014, Combustion and flame.

[174]  Mingfa Yao,et al.  Combustion and emissions of 2,5-dimethylfuran addition on a diesel engine with low temperature combustion , 2013 .

[175]  G. Marin,et al.  The thermal decomposition of 2,5-dimethylfuran , 2012 .

[176]  C. Law On self-acceleration of cellular spherical flames , 2011 .

[177]  Yiguang Ju,et al.  Effects of Lewis number and ignition energy on the determination of laminar flame speed using propagating spherical flames , 2009 .

[178]  L. Cox-Fuenzalida,et al.  An Experimental Analysis , 2007 .

[179]  C. Law,et al.  Cellular instabilities of expanding hydrogen/propane spherical flames at elevated pressures: theory and experiment , 2005 .

[180]  Chung King Law,et al.  Morphology and burning rates of expanding spherical flames in H2/O2/inert mixtures up to 60 atmospheres , 2000 .

[181]  Robert C. Wolpert,et al.  A Review of the , 1985 .

[182]  R. S. Benson,et al.  Internal Combustion Engines: A Detailed Introduction to the Thermodynamics of Spark and Compression Ignition Engines, Their Design and Development , 1979 .