Thermal fatigue of materials for die-casting tooling

Abstract This research is conducted to study the thermal fatigue resistance of different hot-work tool steels; AISI H11 and H13, special tool steel and 18% Ni maraging steel. The maraging steel is surface cladded by GTA welding to study the thermal fatigue resistance of surface layer. An influence of mechanical and microstructural properties on thermal fatigue resistance is evaluated. An innovative apparatus for thermal fatigue testing is developed to study the thermal fatigue resistance. The test specimens are subjected to cyclic heating in bath of molten Aluminum Alloy 226 and cooling in bath of water-based lubricant. They are continuously internally cooled with cold water. The specimens are periodically analyzed after completion of particular number of cycles. The microstructure, hardness profile and the surface cracks developed are analyzed. Temperature transients at different locations of test specimen are measured and used in computation of transient stresses performed by finite elements. The specimens of special geometry are developed using finite element modeling to improve testing efficiency. An optimal set of thermal fatigue testing parameters are developed to establish efficient testing. The influence of thermal loading on tempering of hot work tool steel and on aging of maraging steel claddings during testing is determined. The results showed significant differences in thermal fatigue resistance of tested materials and their heat treatments. The best thermal fatigue resistance achieved special tool steel due to its high thermal stability. The resistance of AISI H11 tool steel is slightly superior to that of maraging steel weld.

[1]  J. Bergström,et al.  Thermal fatigue testing of chromium martensitic hot-work tool steel after different austenitizing treatments , 2004 .

[2]  P. Panjan,et al.  Improvement of die-casting tools with duplex treatment , 2004 .

[3]  Janez Tušek,et al.  Finite element modeling of GTA weld surfacing applied to hot-work tooling , 2004 .

[4]  R. Shivpuri,et al.  A multilayer coating architecture to reduce heat checking of die surfaces , 2003 .

[5]  V. Velay,et al.  Cyclic behaviour simulation of X38CRMOV5-47HRC (AISI H11)-tempered martensitic hot-work tool steel , 2006 .

[6]  Rajiv Shivpuri,et al.  Computer modeling and prediction of thermal fatigue cracking in die-casting tooling , 2004 .

[7]  J. Tušek,et al.  Aging of maraging steel welds during aluminium alloy die casting , 2008 .

[8]  Janez Kopac,et al.  Analysis of casting die failures , 2001 .

[9]  B. Taljat,et al.  Suitability of maraging steel weld cladding for repair of die casting tooling , 2008 .

[10]  P. Panjan,et al.  Improvement of tool life of die-casting tools with duplex treatment , 2006 .

[11]  J. Tušek,et al.  Suitability of Maraging Steel Weld Cladding for Repair of Die-Casting Tooling , 2009 .

[12]  Sture Hogmark,et al.  Thermal fatigue cracking of surface engineered hot work tool steels , 2005 .

[13]  P. Lamesle,et al.  Fatigue-oxidation interaction models for life prediction of hot forming tools steels under transient thermomechanical loadings , 2008 .

[14]  Janez Tušek,et al.  Thermal stresses in aluminium alloy die casting dies , 2008 .

[15]  John F. Wallace,et al.  Evaluation of soldering, washout and thermal fatigue resistance of advanced metal materials for aluminum die-casting dies , 2004 .

[16]  R. Shivpuri,et al.  Thermal cracking behavior of multi-layer LAFAD coatings on nitrided die steels in liquid aluminum processing , 2002 .

[17]  J. Bergström,et al.  High temperature fatigue of tool steels , 2006 .

[18]  R. Shivpuri,et al.  Intermetallic formation and its relation to interface mass loss and tribology in die casting dies , 2004 .

[19]  Sture Hogmark,et al.  Simulation and evaluation of thermal fatigue cracking of hot work tool steels , 2004 .

[20]  S. Hogmark,et al.  Failure modes in field-tested brass die casting dies , 2004 .

[21]  Yucong Wang.  A study of PVD coatings and die materials for extended die-casting die life , 1997 .

[22]  R. Shivpuri,et al.  Dissolution and soldering behavior of nitrided hot working steel with multilayer LAFAD PVD coatings , 2001 .

[23]  Yu Wang,et al.  Thermal fatigue behavior of an iron-based laser sintered material , 2009 .