Performance comparison between textured, pocket, and tapered-land sector-pad thrust bearings using computational fluid dynamics thermohydrodynamic analysis

Different geometry patterns of the surface of thrust bearings have been proven very beneficial in terms of bearing load-carrying capacity and friction coefficient. In this study, four different types of sector-pad thrust bearings have been cross-evaluated for operation under realistic operating conditions: (a) an open pocket bearing, (b) a closed pocket bearing, (c) a tapered-land bearing, and (d) a bearing partially textured with rectangular dimples. Bearing performance has been computed by means of computational fluid dynamics simulations based on the numerical solution of the Navier–Stokes and energy equations for incompressible flow. Conjugate heat transfer at the bearing pad and rotor has been taken into account. Initially, for a reference design of each bearing, the effects of varying rotational speed and minimum film thickness have been investigated. Further, characterization of each bearing for a constant level of thrust load has been performed. Finally, the effects of varying the depth of each geometry pattern have been studied. The present results illustrate a superior performance of the open pocket bearing in comparison to the other bearing types.

[1]  M. Fillon,et al.  Analytical investigation of a partially textured parallel slider , 2009 .

[2]  Iraj Mirzaee,et al.  An analytical approach for analysis and optimisation of slider bearings with infinite width parallel textures , 2010 .

[3]  Sergei Glavatskih,et al.  Pressure Buildup Mechanism in a Textured Inlet of a Hydrodynamic Contact , 2008 .

[4]  Pantelis G. Nikolakopoulos,et al.  Characterization of Stiffness and Damping in Textured Sector Pad Micro Thrust Bearings Using Computational Fluid Dynamics , 2012 .

[5]  Niels Heinrichson.  On the Design of Tilting-Pad Thrust Bearings , 2007 .

[6]  C. Papadopoulos,et al.  Computational Fluid Dynamics Thermohydrodynamic Analysis of Three-Dimensional Sector-Pad Thrust Bearings With Rectangular Dimples , 2014 .

[7]  M. Fillon,et al.  An experimental analysis of the hydrodynamic contribution of textured thrust bearings during steady-state operation: A comparison with the untextured parallel surface configuration , 2015 .

[8]  Izhak Etsion,et al.  Experimental Investigation of Laser Surface Textured Parallel Thrust Bearings , 2004 .

[9]  Pantelis G. Nikolakopoulos,et al.  Geometry Optimization of Textured Three-Dimensional Micro- Thrust Bearings , 2011 .

[10]  Pantelis G. Nikolakopoulos,et al.  Geometry Optimization of Textured 3-D Micro-Thrust Bearings , 2011 .

[11]  Michel Fillon,et al.  CFD THERMOHYDRODYNAMIC ANALYSIS OF 3-D SECTOR-PAD THRUST BEARINGS WITH RECTANGULAR DIMPLES , 2013 .

[12]  Hugh Spikes,et al.  CFD analysis of a low friction pocketed pad bearing , 2005 .

[13]  Michel Fillon,et al.  Performance of a Hydrodynamic Fixed Geometry Thrust Bearing: Comparison between Experimental Data and Numerical Results , 2006 .

[14]  Maurice Godet,et al.  Hydrodynamic Lubrication: Bearings and Thrust Bearings , 1997 .

[15]  V G Marian,et al.  Theoretical and experimental analysis of a partially textured thrust bearing with square dimples , 2007 .

[16]  Michel Fillon,et al.  THERMOHYDRODYNAMIC BEHAVIOR OF A SLIDER POCKET BEARING , 2006 .

[17]  M. Fillon,et al.  About the validity of Reynolds equation and inertia effects in textured sliders of infinite width , 2009 .

[18]  R. Rahmani,et al.  Optimization of Partially Textured Parallel Thrust Bearings with Square-Shaped Micro-Dimples , 2007 .

[19]  Dennis V. De Pellegrin,et al.  An isoviscous, isothermal model investigating the influence of hydrostatic recesses on a spring-supported tilting pad thrust bearing , 2012 .

[20]  Michel Fillon,et al.  Experiments on Thermal Effects in a Hydrodynamic Thrust Bearing , 1998 .

[21]  Gwidon Stachowiak,et al.  Engineering Tribology: Fourth Edition , 2013 .

[22]  M. Fillon,et al.  Optimizing surface texture for hydrodynamic lubricated contacts using a mass-conserving numerical approach , 2010 .

[23]  Izhak Etsion.  State of the Art in Laser Surface Texturing , 2004 .

[24]  K. Yagi,et al.  Balancing Wedge Action: A Contribution of Textured Surface to Hydrodynamic Pressure Generation , 2013, Tribology Letters.