Formation mechanism of the α variant and its influence on the tensile properties of laser solid formed Ti-6Al-4V titanium alloy

Abstract Laser solid forming (LSF) is a newly developed additive manufacturing which offers a less material waste and reduction in lead-time for fabricating aerospace titanium alloys components. In this paper, two types of block with different build dimension (section geometries) were fabricated by LSF with same processing parameters. The corresponding microstructure, texture, and tensile properties were investigated systematically. The results show that the samples exhibits similar columnar β grains morphology and 〈100〉 fiber texture, but very different α variant characterizations (morphology and texture) due to the different thermal history they experienced respectively. The fine basket-weave microstructure with weak texture can be obtained under the fast cooling conditions, while the colony microstructure shows a strong transformation texture as a result of variant selection in the relative slow cooling rate. The α characterizations depend strongly on the competition growth mechanism between the α WGB (grin boundary Widmanstatten structure) and α I (intragranular α nuclei) during cooling process. The presence of α GB (grain boundary α layers) enhances the nucleation of certain variants in β→α phase transformation. Tensile results reveal that fine basket-weave microstructure has relative high strength and ductility with dimple fracture mode. The colony microstructure shows a feature of dominant brittle fracture appearance and results in low tensile ductility.

[1]  Q. Chao,et al.  Variant selection and intervariant crystallographic planes distribution in martensite in a Ti-6Al-4V alloy , 2014 .

[2]  Hua-ming Wang,et al.  Microstructure evolution and layer bands of laser melting deposition Ti–6.5Al–3.5Mo–1.5Zr–0.3Si titanium alloy , 2014 .

[3]  Xin Lin,et al.  Texture and microstructure characterization in laser additive manufactured Ti–6Al–2Zr–2Sn–3Mo–1.5Cr–2Nb titanium alloy , 2015 .

[4]  Jing Li,et al.  Variant selection in laser melting deposited α + β titanium alloy , 2016 .

[5]  A. Mertens,et al.  Laser cladding as repair technology for Ti–6Al–4V alloy: Influence of building strategy on microstructure and hardness , 2015 .

[6]  B. Van Hooreweder,et al.  Crack propagation and fracture toughness of Ti6Al4V alloy produced by selective laser melting , 2015 .

[7]  Dong Liu,et al.  Microstructure and mechanical behavior of commercial purity Ti/Ti–6Al–2Zr–1Mo–1V structurally graded material fabricated by laser additive manufacturing , 2014 .

[8]  Yang He,et al.  Nucleation and growth mechanism of α-lamellae of Ti alloy TA15 cooling from an α + β phase field , 2013 .

[9]  Jilt Sietsma,et al.  Three-dimensional analysis of microstructures in titanium , 2010 .

[10]  G. Lütjering.  Influence of processing on microstructure and mechanical properties of (α+β) titanium alloys , 1998 .

[11]  Weidong Huang,et al.  Microstructure and anisotropic tensile behavior of laser additive manufactured TC21 titanium alloy , 2016 .

[12]  Xin Lin,et al.  Grain morphology control and texture characterization of laser solid formed Ti6Al2Sn2Zr3Mo1.5Cr2Nb titanium alloy , 2016 .

[13]  G. Spanos,et al.  Sympathetic nucleation: an overview , 1995 .

[14]  J. Kruth,et al.  A study of the microstructural evolution during selective laser melting of Ti–6Al–4V , 2010 .

[15]  E. Reutzel,et al.  Thermo-mechanical model development and validation of directed energy deposition additive manufacturing of Ti–6Al–4V , 2015 .

[16]  F. Zhang,et al.  Predicting phase equilibrium, phase transformation, and microstructure evolution in titanium alloys , 2005 .

[17]  Xin Lin,et al.  Influence of solution treatment on microstructure evolution of TC21 titanium alloy with near equiaxed β grains fabricated by laser additive manufacture , 2016 .

[18]  M. Preuss,et al.  Capturing the texture changes in a zirconium alloy during the allotropic phase transformation , 2009 .

[19]  S. Kelly,et al.  Microstructural evolution in laser-deposited multilayer Ti-6Al-4V builds: Part II. Thermal modeling , 2004 .

[20]  Iain Todd,et al.  Normalised model-based processing diagrams for additive layer manufacture of engineering alloys , 2016 .

[21]  Chee Kai Chua,et al.  Graded microstructure and mechanical properties of additive manufactured Ti–6Al–4V via electron beam melting , 2015 .

[22]  Todd Palmer,et al.  Anisotropic tensile behavior of Ti-6Al-4V components fabricated with directed energy deposition additive manufacturing , 2015 .

[23]  Matthew S. Dargusch,et al.  Controlling the microstructure and properties of wire arc additive manufactured Ti–6Al–4V with trace boron additions , 2015 .

[24]  A. A. Salem,et al.  Variant Selection During Cooling after Beta Annealing of Ti-6Al-4V Ingot Material , 2012, Metallurgical and Materials Transactions A.

[25]  P. Prangnell,et al.  Effect of Wall Thickness Transitions on Texture and Grain Structure in Additive Layer Manufacture (ALM) of Ti-6Al-4V , 2012 .

[26]  H. J. Rack,et al.  Phase transformations during cooling in α+β titanium alloys , 1998 .

[27]  J. Mei,et al.  Influence of position and laser power on thermal history and microstructure of direct laser fabricated Ti–6Al–4V samples , 2005 .

[28]  Anil Chaudhary,et al.  Texture Evolution During Laser Direct Metal Deposition of Ti-6Al-4V , 2016 .

[29]  Ryan R. Dehoff,et al.  Thermal effects on microstructural heterogeneity of Inconel 718 materials fabricated by electron beam melting , 2014 .

[30]  H. Fraser,et al.  Precipitation of grain boundary α in a laser deposited compositionally graded Ti–8Al–xV alloy – an orientation microscopy study , 2004 .

[31]  Yanyan Zhu,et al.  Microstructure and mechanical properties of hybrid fabricated Ti–6.5Al–3.5Mo–1.5Zr–0.3Si titanium alloy by laser additive manufacturing , 2014 .

[32]  Ma Qian,et al.  Additive manufacturing of strong and ductile Ti–6Al–4V by selective laser melting via in situ martensite decomposition , 2015 .

[33]  Nima Shamsaei,et al.  Fatigue behavior and failure mechanisms of direct laser deposited Ti–6Al–4V , 2016 .

[34]  Yanyan Zhu,et al.  Grain morphology evolution behavior of titanium alloy components during laser melting deposition additive manufacturing , 2015 .