Low-frequency meandering piezoelectric vibration energy harvester

The design, fabrication, and characterization of a novel low-frequency meandering piezoelectric vibration energy harvester is presented. The energy harvester is designed for sensor node applications where the node targets a width-tolength aspect ratio close to 1:1 while simultaneously achieving a low resonant frequency. The measured power output and normalized power density are 118 μW and 5.02 μW/mm3/g2, respectively, when excited by an acceleration magnitude of 0.2 g at 49.7 Hz. The energy harvester consists of a laser-machined meandering PZT bimorph. Two methods, strain-matched electrode (SME) and strain-matched polarization (SMP), are utilized to mitigate the voltage cancellation caused by having both positive and negative strains in the piezoelectric layer during operation at the meander's first resonant frequency. We have performed finite element analysis and experimentally demonstrated a prototype harvester with a footprint of 27 x 23 mm and a height of 6.5 mm including the tip mass. The device achieves a low resonant frequency while maintaining a form factor suitable for sensor node applications. The meandering design enables energy harvesters to harvest energy from vibration sources with frequencies less than 100 Hz within a compact footprint.

[1]  K. Sarabandi,et al.  Electromechanical considerations in developing low-voltage RF MEMS switches , 2003 .

[2]  O. Korostynska.  Energy Harvesting Technologies , 2011 .

[3]  Daniel J. Inman,et al.  Effect of Strain Nodes and Electrode Configuration on Piezoelectric Energy Harvesting From Cantilevered Beams , 2009 .

[4]  D. Peroulis,et al.  Increased-bandwidth, meandering vibration energy harvester , 2011, 2011 16th International Solid-State Sensors, Actuators and Microsystems Conference.

[5]  Jan M. Rabaey,et al.  Energy Scavenging for Wireless Sensor Networks: with Special Focus on Vibrations , 2012 .

[6]  Sang-Gook Kim,et al.  DESIGN CONSIDERATIONS FOR MEMS-SCALE PIEZOELECTRIC MECHANICAL VIBRATION ENERGY HARVESTERS , 2005 .

[7]  Chengkuo Lee,et al.  Piezoelectric MEMS Energy Harvester for Low-Frequency Vibrations With Wideband Operation Range and Steadily Increased Output Power , 2011, Journal of Microelectromechanical Systems.

[8]  Daniel J. Inman,et al.  Electromechanical Modeling of the Low-Frequency Zigzag Micro-Energy Harvester , 2011 .

[9]  Paul K. Wright,et al.  A piezoelectric vibration based generator for wireless electronics , 2004 .

[10]  Gaetano Marrocco,et al.  Evolutionary design of miniaturized meander-line antennas for RFID applications , 2002, IEEE Antennas and Propagation Society International Symposium (IEEE Cat. No.02CH37313).

[11]  Henry A. Sodano,et al.  A review of power harvesting using piezoelectric materials (2003–2006) , 2007 .

[12]  D. Leo,et al.  Laser-machined piezoelectric cantilevers for mechanical energy harvesting , 2008, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[13]  Tao Dong,et al.  Modeling and experimental verification of low-frequency MEMS energy harvesting from ambient vibrations , 2011 .

[14]  D. J. Inman,et al.  Parametric Study of Zigzag Microstructure for Vibrational Energy Harvesting , 2012, Journal of Microelectromechanical Systems.

[15]  N. Dutoit,et al.  PERFORMANCE OF MICROFABRICATED PIEZOELECTRIC VIBRATION ENERGY HARVESTERS , 2006 .

[16]  D. Inman,et al.  A Review of Power Harvesting from Vibration using Piezoelectric Materials , 2004 .

[17]  Sang-Gook Kim,et al.  MEMS power generator with transverse mode thin film PZT , 2005 .

[18]  Shadrach Roundy,et al.  On the Effectiveness of Vibration-based Energy Harvesting , 2005 .

[19]  Daniel J. Inman,et al.  Analytical Modeling and Experimental Verification of the Vibrations of the Zigzag Microstructure for Energy Harvesting , 2011 .

[20]  H. Toshiyoshi,et al.  A two-axis piezoelectric tilting micromirror with a newly developed PZT-meandering actuator , 2007, 2007 IEEE 20th International Conference on Micro Electro Mechanical Systems (MEMS).

[21]  Byunghoo Jung,et al.  COMPACT LOW FREQUENCY MEANDERED PIEZOELECTRIC ENERGY HARVESTER , 2009 .

[22]  W.P. Robbins,et al.  High-displacement piezoelectric actuator utilizing a meander-line geometry I. Experimental characterization , 1991, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[23]  Kee S. Moon,et al.  Single crystal piezoelectric transducers to harvest vibration energy , 2005, International Symposium on Optomechatronic Technologies.

[24]  Y. V. Andel,et al.  Vibration energy harvesting with aluminum nitride-based piezoelectric devices , 2009 .

[25]  Kazuhiko Adachi,et al.  An Experimental Power Generation Evaluation of Cantilever Type of Piezoelectric Vibration Energy Harvester , 2009 .

[26]  S. Priya,et al.  Piezoelectric Microgenerators-Current Status and Challenges , 2009, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[27]  P. Wright,et al.  A SELF-POWERED WIRELESS SENSOR FOR INDOOR ENVIRONMENTAL MONITORING , 2004 .

[28]  Norman M. Wereley,et al.  Energy Harvesting Utilizing Single Crystal PMN-PT Material and Application to a Self-Powered Accelerometer , 2009 .

[29]  Paul K. Wright,et al.  A STUDY OF AMBIENT VIBRATIONS FOR PIEZOELECTRIC ENERGY CONVERSION , 2009 .

[30]  Daniel J. Inman,et al.  An experimentally validated bimorph cantilever model for piezoelectric energy harvesting from base excitations , 2009 .