Fabrication of a high strength and ductility Ti‒22Al‒25Nb alloy from high energy ball-milled powder by spark plasma sintering

Abstract A high strength and ductility Ti‒22Al‒25Nb alloy was fabricated from high energy ball-milled powder by spark plasma sintering. The pre-alloyed powder with a normal composition (at %) of 53 Ti, 22 Al and 25 Nb was firstly ball-milled for different milling times, and subsequently consolidated by spark plasma sintering. The effects of ball-milling time on the microstructure and mechanical properties of the ball-milled powder and sintered compact were investigated. The Ti‒22Al‒25Nb alloy sintered by SPS at 950 °C for 10 min under a pressure of 50 MPa from the ball-milled powder showed the microstructure with a large amount of ultrafine/nano O-phase. The best balance of tensile properties was exhibited in the Ti‒22Al‒25Nb alloy sintered from the ball-milled powder for 20 h; the yield strength, the tensile strength and the elongation to failure were 1092 MPa, 1105 MPa and 9.4% at room temperature respectively, exceeding other coarse grain Ti‒22Al‒25Nb alloys fabricated by other powder metallurgy methods in the comprehensive tensile property. The precipitation of secondary phase, the grain refinement and the change of residual dislocation density in the sintered alloy directly affected the tensile properties of the sintered alloy.

[1]  Kai-feng Zhang,et al.  Microstructure and mechanical properties of Ti–22Al–25Nb alloy fabricated by vacuum hot pressing sintering , 2014 .

[2]  P. Cao,et al.  The mechanical behaviour of an ultrafine grained Ti–47Al–2Cr (at%) alloy in tension and compression and at different temperatures , 2011 .

[3]  Jian Lu,et al.  Fabrication of a powder metallurgy Ti2AlNb-based alloy by spark plasma sintering and associated microstructure optimization , 2016 .

[4]  E. Pereloma,et al.  An alternative physical explanation of the Hall–Petch relation , 2004 .

[5]  Jingshen Wu,et al.  High-strength Ti–6Al–4V with ultrafine-grained structure fabricated by high energy ball milling and spark plasma sintering , 2013 .

[6]  Y. H. Li,et al.  Ultrafine-grained Ti-based composites with high strength and low modulus fabricated by spark plasma sintering , 2013 .

[7]  M. Korchagin,et al.  High temperature synthesis of single-phase Ti3Al intermetallic compound in mechanically activated powder mixture , 2013 .

[8]  Yuehui He,et al.  Reaction mechanism in high Nb containing TiAl alloy by elemental powder metallurgy , 2006 .

[9]  N. Fujitsuna,et al.  Effects of lamellar spacing, volume fraction and grain size on creep strength of fully lamellar TiAl alloys , 1997 .

[10]  C. M. Ward-Close,et al.  Microstructure and tensile properties of mechanically alloyed Ti–6A1–4V with boron additions , 2000 .

[11]  Evan Ma,et al.  Microsample tensile testing of nanocrystalline copper , 2003 .

[12]  Subra Suresh,et al.  Mechanical behavior of nanocrystalline metals and alloys , 2003 .

[13]  S. Lele,et al.  Phase stability and ordering behaviour of the O phase in TiAlNb alloys , 1995 .

[14]  C. Servant,et al.  On the B2→O phase transformation in Ti–Al–Nb alloys , 2003 .

[15]  D. Shan,et al.  Investigation of the phase transformations in Ti-22Al-25Nb alloy , 2016 .

[16]  J. Kumpfert.  Intermetallic Alloys Based on Orthorhombic Titanium Aluminide , 2001 .

[17]  C. Suryanarayana,et al.  Mechanical alloying and milling , 2004 .

[18]  Zhang Jianwei,et al.  The enhanced tensile property by introducing bimodal size distribution of lamellar O for O+B2 Ti2AlNb based alloy , 2013 .

[19]  Bingyun Li,et al.  Microstructure and high temperature tensile properties of Ti22Al25Nb alloy prepared by reactive sintering with element powders , 2014 .

[20]  Rui Yang,et al.  Microstructure Design and Heat Response of Powder Metallurgy Ti2AlNb Alloys , 2015 .

[21]  Jing Shi,et al.  Effect of mechanical alloying on the microstructure and properties of W–Ti alloys fabricated by spark plasma sintering , 2016 .

[22]  C. F. Yolton,et al.  Powder metallurgy processing and properties of the ordered orthorhombic alloy Ti-22at.%Al-23at.%Nb , 1995 .

[23]  B. Kong,et al.  Enhanced mechanical properties of orthorhombic Ti2AlNb-based intermetallic alloy , 2003 .

[24]  Lai‐Chang Zhang,et al.  Ultrafine grained Ti-based composites with ultrahigh strength and ductility achieved by equiaxing microstructure , 2015 .

[25]  Jian-lei Yang,et al.  Microstructure and mechanical properties of Ti–22Al–25Nb alloy fabricated by elemental powder metallurgy , 2016 .

[26]  Y. Li,et al.  Bimodal-grained Ti fabricated by high-energy ball milling and spark plasma sintering , 2016 .

[27]  Z. Lei,et al.  Study on laser welding of a Ti-22Al-25Nb alloy: Microstructural evolution and high temperature brittle behavior , 2016 .

[28]  X. Sauvage,et al.  Influence of spark plasma sintering conditions on the sintering and functional properties of an ultra-fine grained 316L stainless steel obtained from ball-milled powder , 2016 .

[29]  B. Majumdar,et al.  Part I. The microstructural evolution in Ti-Al-Nb O+Bcc orthorhombic alloys , 1999 .

[30]  C. Suryanarayana,et al.  Synthesis of stable and metastable phases in the NiSi system by mechanical alloying , 2016 .

[31]  Young-Won Kim.  Strength and ductility in TiAl alloys , 1998 .