A Lateral Differential Resonant Pressure Microsensor Based on SOI-Glass Wafer-Level Vacuum Packaging

This paper presents the fabrication and characterization of a resonant pressure microsensor based on SOI-glass wafer-level vacuum packaging. The SOI-based pressure microsensor consists of a pressure-sensitive diaphragm at the handle layer and two lateral resonators (electrostatic excitation and capacitive detection) on the device layer as a differential setup. The resonators were vacuum packaged with a glass cap using anodic bonding and the wire interconnection was realized using a mask-free electrochemical etching approach by selectively patterning an Au film on highly topographic surfaces. The fabricated resonant pressure microsensor with dual resonators was characterized in a systematic manner, producing a quality factor higher than 10,000 (~6 months), a sensitivity of about 166 Hz/kPa and a reduced nonlinear error of 0.033% F.S. Based on the differential output, the sensitivity was increased to two times and the temperature-caused frequency drift was decreased to 25%.

[1]  Reza Abdolvand,et al.  An advanced reactive ion etching process for very high aspect-ratio sub-micron wide trenches in silicon , 2008 .

[2]  Kyoichi Ikeda,et al.  Various applications of resonant pressure sensor chip based on 3-D micromachining , 1999 .

[3]  R. P. Frankenthal,et al.  The Anodic Corrosion of Gold in Concentrated Chloride Solutions , 1982 .

[4]  Junbo Wang,et al.  A Resonant Pressure Microsensor Capable of Self-Temperature Compensation , 2015, Sensors.

[5]  Junseok Chae,et al.  Fabrication and Characterization of a Wafer-Level MEMS Vacuum Package With Vertical Feedthroughs , 2008, Journal of Microelectromechanical Systems.

[6]  T. Akin,et al.  A method and electrical model for the anodic bonding of SOI and glass wafers , 2012, 2012 IEEE 25th International Conference on Micro Electro Mechanical Systems (MEMS).

[7]  Shouliang Lai,et al.  Aspect ratio dependent etching lag reduction in deep silicon etch processes , 2006 .

[8]  Antti Säynätjoki,et al.  Application of ultra-thin aluminum oxide etch mask made by atomic layer deposition technique , 2007 .

[9]  Fook Siong Chau,et al.  Yield improvement for anodic bonding with suspending structure , 2008 .

[10]  J. Greenwood,et al.  A high accuracy resonant pressure sensor by fusion bonding and trench etching , 1999 .

[11]  Guizhang Lu,et al.  Modeling and simulation of the lag effect in a deep reactive ion etching process , 2006 .

[12]  Junbo Wang,et al.  A High-Q Resonant Pressure Microsensor with Through-Glass Electrical Interconnections Based on Wafer-Level MEMS Vacuum Packaging , 2014, Sensors.

[13]  N. Najafi,et al.  An all-glass chip-scale MEMS package with variable cavity pressure , 2006 .

[14]  Göran Stemme,et al.  Localized removal of the Au-Si eutectic bonding layer for the selective release of microstructures , 2009 .

[15]  P. Kinnell,et al.  Advances in Silicon Resonant Pressure Transducers , 2009 .

[16]  Yilong Hao,et al.  The compatibility of ZnO piezoelectric film with micromachining process , 2003 .

[17]  T. W. Kenny,et al.  Resonant pressure sensor with on-chip temperature and strain sensors for error correction , 2013, 2013 IEEE 26th International Conference on Micro Electro Mechanical Systems (MEMS).

[18]  Lance Horng,et al.  Parameter optimization for an ICP deep silicon etching system , 2007 .

[19]  Kazuhiro Hane,et al.  Electric feed-through for vacuum package using double-side anodic bonding of silicon-on-insulator wafer , 2013 .

[20]  Xiaodong Sun,et al.  A Micromachined Pressure Sensor with Integrated Resonator Operating at Atmospheric Pressure , 2013, Sensors.

[21]  Junbo Wang,et al.  Design and experiment of a laterally driven micromachined resonant pressure sensor for barometers , 2010 .