Process parameter influence on defects and tensile properties of friction stir welded T-joints on AA6061-T4 sheets

Abstract In this study, AA6061-T4 T-joints characterized by combination modes of T-lap and T-butt were fabricated by friction stir welding with different processing parameters. Defects distributed in the obtained specimens were examined by using a stereo microscope and an optical microscope. Process parameter influence on the distribution and the size of original joint line with severe deformation (OJLwSD) defect was investigated. The microstructures and hardness profiles in the T-joints were studied. Influence factors on T-joints’ tensile properties were discussed. In addition, the fracture mode and the fracture surface of the failure samples were observed and discussed as well.

[1]  Michael A. Sutton,et al.  Banded Microstructure in AA2024-T351 and AA2524-T351 Aluminum Friction Stir Welds: Part I. Metallurgical Studies , 2004 .

[2]  Raouf Fathallah,et al.  Fatigue strength improvement of 5083 H11 Al-alloy T-welded joints by shot peening: experimental characterization and predictive approach , 2005 .

[3]  Rajiv S. Mishra,et al.  Microstructural investigation of friction stir welded 7050-T651 aluminium , 2003 .

[4]  S. Park,et al.  Microstructural factors governing hardness in friction-stir welds of solid-solution-hardened Al alloys , 2001 .

[5]  V. Balasubramanian,et al.  Influences of tool pin profile and axial force on the formation of friction stir processing zone in AA6061 aluminium alloy , 2008 .

[6]  Fabrizio Micari,et al.  On the material flow in FSW of T-joints: Influence of geometrical and tecnological parameters , 2009 .

[7]  Livan Fratini,et al.  Friction Stir Welding of AA6082-T6 T-joints: Process Engineering and Performance Measurement , 2006 .

[8]  Rajiv S. Mishra,et al.  Superplastic deformation behaviour of friction stir processed 7075Al alloy , 2002 .

[9]  S. L. Semiatin,et al.  Continuous dynamic recrystallization during friction stir welding of high strength aluminum alloys , 2000 .

[10]  Livan Fratini,et al.  Mechanical and metallurgical effects of in process cooling during friction stir welding of AA7075-T6 butt joints , 2010 .

[11]  N. Sun,et al.  Hook formation and mechanical properties in AZ31 friction stir spot welds , 2010 .

[12]  F. Micari,et al.  Material Flow in FSW of T-joints: Experimental and Numerical Analysis , 2008 .

[13]  Jesper Henri Hattel,et al.  Material flow in butt friction stir welds in AA2024-T3 , 2006 .

[14]  Mohammad Jahazi,et al.  Effect of tool rotational speed and probe length on lap joint quality of a friction stir welded magnesium alloy , 2011 .

[15]  S. Spigarelli,et al.  Microstructure and mechanical property studies of AA6056 friction stir welded plate , 2007 .

[16]  N. K. Mehta,et al.  The microstructure and mechanical properties of friction stir welded Al–Zn–Mg alloy in as welded and heat treated conditions , 2011 .

[17]  V. Balasubramanian,et al.  Influences of process parameters on tensile strength of friction stir welded cast A319 aluminium alloy joints , 2009 .

[18]  Lawrence E Murr,et al.  A TEM study of precipitation and related microstructures in friction-stir-welded 6061 aluminium , 1998 .

[19]  Livan Fratini,et al.  Friction stir welding of tailored joints for industrial applications , 2009 .

[20]  Weifeng Xu,et al.  Microstructure and mechanical properties of friction stir welded joints in 2219-T6 aluminum alloy , 2009 .

[21]  L. D. Filippis,et al.  Effect of shoulder geometry on residual stress and fatigue properties of AA6082 fsw joints , 2009 .

[22]  Antonie Oosterkamp,et al.  Kissing Bond Phenomena in Solid-State Welds of Aluminum Alloys , 2004 .

[23]  Tracy W. Nelson,et al.  Microstructure evolution during FSW/FSP of high strength aluminum alloys , 2005 .

[24]  Hiroyuki Kokawa,et al.  Characteristics of the kissing-bond in friction stir welded Al alloy 1050 , 2005 .

[25]  Livan Fratini,et al.  Influence of material characteristics on plastomechanics of the FSW process for T-joints , 2009 .

[26]  P. Moreira,et al.  Friction stir welding of T-joints with dissimilar aluminium alloys: Mechanical joint characterisation , 2010 .

[27]  Livan Fratini,et al.  On the FSW of AA2024-T4 and AA7075-T6 T-joints: an industrial case study , 2010 .

[28]  V. S. Kumar,et al.  Relationship between process parameters and mechanical properties of friction stir processed AA6063-T6 aluminum alloy , 2011 .

[29]  R. Mishra,et al.  Friction stir welding of precipitation strengthened aluminium alloys: Scope and challenges , 2011 .

[30]  Xiao Dong Xu,et al.  Study on the Microstructures and Tensile Behaviors of Friction Stir Welded T-joints for AA6061-T4 Alloys , 2012, Journal of Materials Engineering and Performance.

[31]  C. Muralidharan,et al.  Establishing Empirical Relationships to Predict Grain Size and Tensile Strength of Friction Stir Welded AA 6061-T6 Aluminium Alloy Joints , 2010 .

[32]  X. Sauvage,et al.  Precipitate stability and recrystallisation in the weld nuggets of friction stir welded Al–Mg–Si and Al–Mg–Sc alloys , 2008, 0808.3716.

[33]  R. Thomson,et al.  Geometry and damage effects in a composite marine T-joint , 2004 .

[34]  Z. Ma,et al.  Effect of welding parameters on tensile properties and fracture behavior of friction stir welded Al-Mg-Si alloy , 2007 .

[35]  Livan Fratini,et al.  Residual stresses in friction stir welded parts of complex geometry , 2012 .

[36]  L. Fratini,et al.  Improved FE model for simulation of friction stir welding of different materials , 2010 .

[37]  Xiaodong Xu,et al.  Characteristics of defects and tensile behaviors on friction stir welded AA6061-T4 T-joints , 2012 .

[38]  A. Denquin,et al.  Influence of the Initial Ageing Condition on Microstructure and Properties of a Friction Stir Welded 6056 Alloy , 2002 .

[39]  Rajiv S. Mishra,et al.  Friction Stir Welding and Processing , 2007 .