A study on residential heating energy requirement and optimum insulation thickness

Heat loss from buildings has a considerable share in waste of energy especially in Turkey since no or little insulation is used in existing and new buildings. Therefore, energy savings can be obtained by determining of heat loss characteristics with using proper thickness of insulation. For this purpose, in this study, calculations of optimum insulation thickness are carried out on a prototype building in Bursa as a sample city. Considering long term and current outdoor air temperature records (from 1992 to 2005), degree-hour (DH) values are calculated, and the variation of annual energy requirement of the building is investigated for various architectural design properties (such as air infiltration rate, glazing type, and area). Then, the effects of the insulation thickness on the energy requirement and total cost are presented. Based on life cycle cost (LCC) analysis, the optimum insulation thicknesses are determined for different fuel types. As a conclusion, the length of the heating period is average 221 days, and the mean heating DH value is found as 45113.2 besides changing between 38000 and 55000. The optimum insulation thicknesses for Bursa vary between 5.3 and 12.4cm depending on fuel types. In addition to this, the variation in Turkey is more dramatically.

[1]  Hulya Sarak,et al.  The degree-day method to estimate the residential heating natural gas consumption in Turkey: a case study , 2003 .

[2]  Abdurrahman Satman,et al.  Heating and cooling degree-hours for Turkey , 1999 .

[3]  Khaled A. Al-Sallal.  Comparison between polystyrene and fiberglass roof insulation in warm and cold climates , 2003 .

[4]  Y. Çengel.  Heat Transfer: A Practical Approach , 1997 .

[5]  M. F. Zedan,et al.  Effect of electricity tariff on the optimum insulation-thickness in building walls as determined by a dynamic heat-transfer model , 2005 .

[6]  Z. Şen,et al.  An application of the degree-hours method to estimate the residential heating energy requirement and fuel consumption in Istanbul , 2000 .

[7]  Afif Hasan,et al.  Optimizing insulation thickness for buildings using life cycle cost , 1999 .

[8]  S. A. Al-Sanea,et al.  Effect of insulation location on thermal performance of building walls under steady periodic conditions , 2001 .

[9]  Bilal Akash,et al.  Some prospects of energy savings in buildings , 2001 .

[10]  S. A. Al-Sanea,et al.  Heat Transfer Characteristics and Optimum Insulation Thickness for Cavity Walls , 2003 .

[11]  N. Kyriakis,et al.  Heating and cooling degree-hours for Athens and Thessaloniki, Greece , 2005 .

[12]  Hüsamettin Bulut,et al.  Analysis of variable-base heating and cooling degree-days for Turkey , 2001 .

[13]  R. Ogulata,et al.  Sectoral energy consumption in Turkey , 2002 .

[14]  Orhan Büyükalaca,et al.  Detailed weather data for the provinces covered by the Southeastern Anatolia Project (GAP) of Turkey , 2004 .

[15]  Jamal O. Jaber,et al.  Prospects of energy savings in residential space heating , 2002 .

[16]  K. Kaygusuz,et al.  Energy and Sustainable Development. Part II: Environmental Impacts of Energy Use , 2004 .

[17]  A. Özgenoğlu,et al.  Environmental issues and waste management in energy and mineral production : proceedings of fifth International Symposium on Environmental Issue and Waste Managenent in Energy and Mineral Production , SWEMP'98 Ankara/Turkey/18-20 May 1998 , 1998 .

[18]  Refrigerating.  ASHRAE handbook of fundamentals , 1967 .

[19]  Ali Bolatturk,et al.  Determination of optimum insulation thickness for building walls with respect to various fuels and climate zones in Turkey , 2006 .

[20]  Kamil Kaygusuz,et al.  Energy and Sustainable Development in Turkey. Part I: Energy Utilization and Sustainability , 2002 .