Numerical analysis of tube expansion process for heat exchangers production

This work analyses two different aspects of the mechanical process of tubes expansion used for the production of heat exchangers. In particular, the influences on the expansion process due to mandrel geometry and geometrical errors in tubes, caused by production tolerances, were studied and analyzed using finite element (FE) models. A 2D axisymmetric model was used to study the influence of mandrel geometry, whereas a 3D solid model was adopted to investigate the influence of geometrical errors in tubes. Experimental tests were carried out on actual materials in order to set up and validate the FE models. Force required for expansion, and variation in tube dimensions due to expansion were investigated and a good agreement was found between experimental and FE results. Additionally, the obtained results showed that the fillet radius is the most important geometrical factor of the mandrel in order to reduce the expansion force. A great influence of the tube geometrical errors was observed on the tube expansion process, which can compromise the performance of the heat exchanger. Finally, it is worth mentioning that the present study provides useful information that might be used to improve tubes expansion processes in general and heat exchangers production in particular.

[1]  Tasneem Pervez,et al.  Dynamic Effects of Mandrel/Tubular Interaction on Downhole Solid Tubular Expansion in Well Engineering , 2009 .

[2]  Taylan Altan,et al.  Finite element analysis of tube hydroforming processes in a rectangular die , 2003 .

[3]  Tasneem Pervez,et al.  Finite Element Modeling of a Solid Tubular Expansion - A Typical Well Engineering Application , 2005 .

[4]  Matteo Strano,et al.  FEM analysis of tube pre-bending and hydroforming , 2004 .

[5]  Dayong Li,et al.  An experimental and numerical study of the expansion forming of a thick-walled microgroove tube , 2009 .

[6]  Omar S. Al-Abri,et al.  Optimum mandrel configuration for efficient down-hole tube expansion , 2012 .

[7]  Wing Kam Liu,et al.  Nonlinear Finite Elements for Continua and Structures , 2000 .

[8]  Paulo A.F. Martins,et al.  Expansion and reduction of thin-walled tubes using a die: Experimental and theoretical investigation , 2006 .

[9]  Rashid Khan,et al.  Experimental and Numerical Simulation of In-Situ Tube Expansion for Deep Gas Wells , 2012 .

[10]  Marco Peroni,et al.  MECHANICAL MODELS OF THE BEHAVIOUR OF PLASTIC MATERIALS: INFLUENCE OF TIME AND TEMPERATURE , 2010 .

[11]  Omar S. Al-Abri,et al.  Tube Expansion Under Various Down-Hole End Conditions , 2013 .

[12]  Yinghong Peng,et al.  Numerical and experimental study on expansion forming of inner grooved tube , 2009 .

[13]  Jialing Yang,et al.  Energy absorption of expansion tubes using a conical–cylindrical die: Experiments and numerical simulation , 2010 .

[15]  Omar S. Al-Abri,et al.  Structural behavior of solid expandable tubular undergoes radial expansion process – Analytical, numerical, and experimental approaches , 2013 .

[16]  H. P. Huttelmaier,et al.  API TUBULAR OVALITY AND STRESSES IN HORIZONTAL WELLS WITH A FINITE-ELEMENT METHOD , 1994 .

[17]  A. Seibi,et al.  Structural Behavior of a Solid Tubular Under Large Radial Plastic Expansion , 2005 .

[18]  W-C Chen,et al.  Analysis and finite element simulation of tube expansion in a rectangular cross-sectional die , 2003 .

[19]  Ali Karrech,et al.  Analytical model for the expansion of tubes under tension , 2010 .

[20]  Marco Peroni,et al.  Identification of Strain-Rate Sensitivity Parameters of Steels With an Inverse Method , 2007 .

[21]  B. J. Mac Donald,et al.  Determination of the optimal load path for tube hydroforming processes using a fuzzy load control algorithm and finite element analysis , 2004 .

[22]  M. Finn,et al.  High strain rate tensile testing of automotive aluminum alloy sheet , 2005 .

[23]  T. Pervez,et al.  Experimental and numerical investigation of expandable tubular structural integrity for well applications , 2010 .

[24]  R. D. Mack,et al.  The Effect Of Tubular Expansion On The Mechanical Properties And Performance Of Selected OCTG - Results Of Laboratory Studies , 2005 .

[25]  Arman Molki,et al.  Experimental and Numerical Study of Expanded Aluminum and Steel Tubes , 2011 .

[26]  Tasneem Pervez,et al.  Solid Tubular Expansion in Horizontal Wells , 2007 .

[27]  D. Agard,et al.  Microtubule nucleation by γ-tubulin complexes , 2011, Nature Reviews Molecular Cell Biology.

[28]  Massimiliano Avalle,et al.  Experimental and numerical characterization of a mechanical expansion process for thin-walled tubes , 2014 .

[29]  P. Rosa,et al.  End forming of thin-walled tubes , 2006 .

[30]  Omar S. Al-Abri.  Analytical and Numerical Solution for Large Plastic Deformation of Solid Expandable Tubular , 2011 .

[31]  Dayong Li,et al.  Optimization to the tube–fin contact status of the tube expansion process , 2011 .

[32]  Tasneem Pervez,et al.  Simulation of Solid Tubular Expansion in Well Drilling Using Finite Element Method , 2005 .

[33]  Gilmar Ferreira Batalha,et al.  Experimental and numerical simulation of tube hydroforming (THF) , 2005 .