Frequency Tuning of Work Modes in Z-Axis Dual-Mass Silicon Microgyroscope

Frequency tuning of work modes in the silicon vibratory gyroscope is studied by the theoretical, numerical, and experimental methods in this paper. First, the schematic structure and simplified kinematics model of the gyroscope were presented for deducing the natural frequencies. Then, the width and length of support beams were optimized to tune work frequencies at their designed value. Besides, the frequency difference was experimentally tested and manually tuned by varying the voltage applied on the tuning capacitors. The test on a prototype showed that the difference could be localized between −55.8 Hz and 160.2 Hz when the tuning voltage limit is 20 V. Finally, a frequency control loop was developed to automatically tune the sense frequency toward the drive frequency. Both the theoretical analysis and numeric simulation show that the difference is stabilized at 0.8 Hz when no Coriolis force or quadrature coupling force is applied. It is proved that the frequency difference is successfully tuned by modifying the size of support beams before fabrication as well as the voltage applied on the tuning capacitors after fabrication. The automatic tuning loop, used to match the work modes, is beneficial to enhance the performance of the gyroscope as well as its resistance to environment disturbances.

[1]  J. Bernstein,et al.  A micromachined comb-drive tuning fork rate gyroscope , 1993, [1993] Proceedings IEEE Micro Electro Mechanical Systems.

[2]  N. Barbour,et al.  Micromachined inertial sensors for vehicles , 1997, Proceedings of Conference on Intelligent Transportation Systems.

[3]  Qin Shi.  Device-level Vacuum Packaging of Silicon Microgyroscopes , 2009 .

[4]  M. Dalal,et al.  A mode-matched 0.9 MHZ single proof-mass dual-axis gyroscope , 2011, 2011 16th International Solid-State Sensors, Actuators and Microsystems Conference.

[5]  Farrokh Ayazi,et al.  Micromachined inertial sensors , 1998, Proc. IEEE.

[6]  Yunfang Ni,et al.  Fabrication error analysis on dual-mass silicon micro-gyroscope , 2011, 2011 International Conference on Electrical and Control Engineering.

[7]  Bill Goodwine,et al.  Engineering Differential Equations , 2011 .

[8]  Liwei Lin,et al.  Characterization of selective polysilicon deposition for MEMS resonator tuning , 2003 .

[9]  Bo Yang,et al.  A quadrature error and offset error suppression circuitry for Silicon Micro-Gyroscope , 2008, 2008 3rd IEEE International Conference on Nano/Micro Engineered and Molecular Systems.

[10]  T. Akin,et al.  A single-crystal silicon symmetrical and decoupled gyroscope on insulating substrate , 2003, TRANSDUCERS '03. 12th International Conference on Solid-State Sensors, Actuators and Microsystems. Digest of Technical Papers (Cat. No.03TH8664).

[11]  F. Ayazi,et al.  High Performance Matched-Mode Tuning Fork Gyroscope , 2006, 19th IEEE International Conference on Micro Electro Mechanical Systems.

[12]  F. Ayazi,et al.  A Mode-Matched Silicon-Yaw Tuning-Fork Gyroscope With Subdegree-Per-Hour Allan Deviation Bias Instability , 2008, Journal of Microelectromechanical Systems.

[13]  Roberto Oboe,et al.  Automatic Mode Matching in MEMS Vibrating Gyroscopes Using Extremum-Seeking Control , 2009, IEEE Transactions on Industrial Electronics.

[14]  Andrei M. Shkel.  Micromachined gyroscopes: challenges, design solutions, and opportunities , 2001, SPIE Smart Structures and Materials + Nondestructive Evaluation and Health Monitoring.

[15]  Geometry optimization of a Lorentz force, resonating MEMS magnetometer , 2014, Microelectron. Reliab..

[16]  J. Frech,et al.  Cross-coupling of the oscillation modes of vibratory gyroscopes , 2003, TRANSDUCERS '03. 12th International Conference on Solid-State Sensors, Actuators and Microsystems. Digest of Technical Papers (Cat. No.03TH8664).

[17]  Liwei Lin,et al.  Active frequency tuning for micro resonators by localized thermal stressing effects , 2001 .

[18]  A. Kourepenis,et al.  Error sources in in-plane silicon tuning-fork MEMS gyroscopes , 2006, Journal of Microelectromechanical Systems.

[19]  Vijay K. Varadan.  Micromachined Gyroscopes: Challenges, Design Solutions, and Opportunities , 2003 .

[20]  Ole Sigmund,et al.  Topological design of electromechanical actuators with robustness toward over- and under-etching , 2013 .

[21]  Zayd C. Leseman,et al.  Design and characterization of a low temperature gradient and large displacement thermal actuators for in situ mechanical testing of nanoscale materials , 2012 .

[22]  Andrei M. Shkel,et al.  Micromachined rate gyroscope architecture with ultra-high quality factor and improved mode ordering , 2011 .

[23]  Sangkyung Sung,et al.  On the Mode-Matched Control of MEMS Vibratory Gyroscope via Phase-Domain Analysis and Design , 2009, IEEE/ASME Transactions on Mechatronics.