High-sensitivity triaxial tactile sensor with elastic microstructures pressing on piezoresistive cantilevers

Abstract In this paper, we proposed a design to increase the sensitivity of a piezoresistive-type triaxial tactile sensor. Using conventional piezoresistive tactile sensors, in which the piezoresistive elements were completely embedded inside an elastic block, our proposed tactile sensor design features an air cavity underneath the piezoresistive elements. The cavity was created by pressing an elastic cap with microstructures onto the piezoresistive cantilevers of a sensor chip. We confirmed that the proposed design increased the sensitivity of the tactile sensor by approximately 150 times and 100 times in response to normal and lateral forces, respectively.

[1]  Chang Liu,et al.  A tri-axial touch sensor with direct silicon to PC-board packaging , 2011 .

[2]  I. Shimoyama,et al.  MEMS on robot applications , 2009, TRANSDUCERS 2009 - 2009 International Solid-State Sensors, Actuators and Microsystems Conference.

[3]  P. Dario,et al.  Development and Experimental Analysis of a Soft Compliant Tactile Microsensor for Anthropomorphic Artificial Hand , 2008, IEEE/ASME Transactions on Mechatronics.

[4]  J. R. Hewit,et al.  Tactile sensing technology for minimal access surgery––a review , 2003 .

[5]  Hyung-Kew Lee,et al.  Iop Publishing Journal of Micromechanics and Microengineering Real-time Measurement of the Three-axis Contact Force Distribution Using a Flexible Capacitive Polymer Tactile Sensor , 2022 .

[6]  Haruo Noma,et al.  Fabrication of a Flexible Array for Tactile Sensors with Microcantilevers and the Measurement of the Distribution of Normal and Shear Forces , 2011 .

[7]  Haruo Noma,et al.  Tactile sensor array using microcantilever with nickel–chromium alloy thin film of low temperature coefficient of resistance and its application to slippage detection , 2012 .

[8]  J. Heo,et al.  Tactile sensors using the distributed optical fiber sensors , 2008, 2008 3rd International Conference on Sensing Technology.

[9]  Kaspar Althoefer,et al.  Tactile sensing for dexterous in-hand manipulation in robotics-A review , 2011 .

[10]  K. Matsumoto,et al.  Shear force detector using piezo-resistive beams with sidewall-doping , 2012, 2012 IEEE 25th International Conference on Micro Electro Mechanical Systems (MEMS).

[11]  I. Shimoyama,et al.  High sensitive 3D tactile sensor with the structure of elastic pyramids on piezoresistive cantilevers , 2013, 2013 IEEE 26th International Conference on Micro Electro Mechanical Systems (MEMS).

[12]  I. Shimoyama,et al.  Force sensing submicrometer thick cantilevers with ultra-thin piezoresistors by rapid thermal diffusion , 2004 .

[13]  Tetsuo Kan,et al.  Design of a piezoresistive triaxial force sensor probe using the sidewall doping method , 2013 .

[14]  Nan-Chyuan Tsai,et al.  Development of tactile sensors for simultaneous, detection of normal and shear stresses , 2010 .

[15]  E. Kolesar,et al.  Object imaging with a piezoelectric robotic tactile sensor , 1993, Proceedings of the IEEE 1993 National Aerospace and Electronics Conference-NAECON 1993.

[16]  Thomas W. Kenny,et al.  Low‐stiffness silicon cantilevers for thermal writing and piezoresistive readback with the atomic force microscope , 1996 .

[17]  Lucia Beccai,et al.  Development of a bioinspired MEMS based capacitive tactile sensor for a robotic finger , 2011 .

[18]  Nawid Jamali,et al.  Material classification by tactile sensing using surface textures , 2010, 2010 IEEE International Conference on Robotics and Automation.