Study of the kinetics and mechanism of rapid self-assembly in block copolymer thin films during solvo-microwave annealing.

Microwave annealing is an emerging technique for achieving ordered patterns of block copolymer films on substrates. Little is understood about the mechanisms of microphase separation during the microwave annealing process and how it promotes the microphase separation of the blocks. Here, we use controlled power microwave irradiation in the presence of tetrahydrofuran (THF) solvent, to achieve lateral microphase separation in high-χ lamellar-forming poly(styrene-b-lactic acid) PS-b-PLA. A highly ordered line pattern was formed within seconds on silicon, germanium and silicon on insulator (SOI) substrates. In-situ temperature measurement of the silicon substrate coupled to condition changes during "solvo-microwave" annealing allowed understanding of the processes to be attained. Our results suggest that the substrate has little effect on the ordering process and is essentially microwave transparent but rather, it is direct heating of the polar THF molecules that causes microphase separation. It is postulated that the rapid interaction of THF with microwaves and the resultant temperature increase to 55 °C within seconds causes an increase of the vapor pressure of the solvent from 19.8 to 70 kPa. This enriched vapor environment increases the plasticity of both PS and PLA chains and leads to the fast self-assembly kinetics. Comparing the patterns formed on silicon, germanium and silicon on insulator (SOI) and also an in situ temperature measurement of silicon in the oven confirms the significance of the solvent over the role of substrate heating during "solvo-microwave" annealing. Besides the short annealing time which has technological importance, the coherence length is on a micron scale and dewetting is not observed after annealing. The etched pattern (PLA was removed by an Ar/O2 reactive ion etch) was transferred to the underlying silicon substrate fabricating sub-20 nm silicon nanowires over large areas demonstrating that the morphology is consistent both across and through the film.

[1]  M. Morris,et al.  Swift nanopattern formation of PS-b-PMMA and PS-b-PDMS block copolymer films using a microwave assisted technique. , 2013, ACS nano.

[2]  S. Gabriel,et al.  Dielectric parameters relevant to microwave dielectric heating , 1998 .

[3]  Fajun Zhang,et al.  Effect of crystallization on the lamellar orientation in thin films of symmetric poly(styrene)-b-poly(L-lactide) diblock copolymer , 2006 .

[4]  M. Hillmyer,et al.  Non-lift-off block copolymer lithography of 25 nm magnetic nanodot arrays. , 2011, ACS applied materials & interfaces.

[5]  D. Michael P. Mingos,et al.  Applications of Microwave Dielectric Heating Effects to Synthetic Problems in Chemistry , 1991 .

[6]  F. Bates,et al.  Unifying Weak- and Strong-Segregation Block Copolymer Theories , 1996 .

[7]  L. Pauling.  The Nature Of The Chemical Bond , 1939 .

[8]  Peter Trefonas,et al.  Designing new materials and processes for directed self-assembly applications , 2012, Advanced Lithography.

[9]  D. Herr.  Directed block copolymer self-assembly for nanoelectronics fabrication , 2011 .

[10]  E. Hanamura,et al.  Microwave Absorption in Silicon at Low Temperatures , 1964 .

[11]  D. Mingos,et al.  Applications of Microwave Dielectric Heating Effects to Synthetic Problems in Chemistry , 1991 .

[12]  Shouwu Guo,et al.  Perpendicular Domain Orientation in Thin Films of Polystyrene−Polylactide Diblock Copolymers , 2005 .

[13]  Jeffrey N. Murphy,et al.  Deconvoluting the mechanism of microwave annealing of block copolymer thin films. , 2014, ACS nano.

[14]  Freddy Yin Chiang Boey,et al.  Thermal and non-thermal interaction of microwave radiation with materials , 1995, Journal of Materials Science.

[15]  Andrew K. Whittaker,et al.  EUVL compatible LER solutions using functional block copolymers , 2012, Advanced Lithography.

[16]  Jillian M. Buriak,et al.  Rapid Assembly of Nanolines with Precisely Controlled Spacing from Binary Blends of Block Copolymers , 2011 .

[17]  J. R. Gliessman,et al.  The Resistivity and Hall Effect of Germanium at Low Temperatures , 1950 .

[18]  Marcus Müller,et al.  Rapid Directed Assembly of Block Copolymer Films at Elevated Temperatures , 2008 .

[19]  P. Nealey,et al.  Epitaxial self-assembly of block copolymers on lithographically defined nanopatterned substrates , 2003, Nature.

[20]  R. Szoszkiewicz,et al.  Local thermomechanical analysis of a microphase-separated thin lamellar PS-b-PEO film. , 2012, Langmuir : the ACS journal of surfaces and colloids.

[21]  Jeffrey N. Murphy,et al.  Fast assembly of ordered block copolymer nanostructures through microwave annealing. , 2010, ACS nano.

[22]  A. Baszkin,et al.  Behavior of Poly(D,L-lactic acid) Monolayers at the Air-Water Interface. Effect of Spreading Solvents , 1994 .

[23]  Bao-Tsan Ko,et al.  Solvent-induced microdomain orientation in polystyrene-b-poly(l-lactide) diblock copolymer thin films for nanopatterning , 2005 .

[24]  M. Morris,et al.  Solvent Vapor Annealing of Block Polymer Thin Films , 2013 .

[25]  Shoji Tanaka,et al.  Impurity Conduction inp-Type Silicon at Microwave Frequencies , 1963 .

[26]  M. Hillmyer,et al.  Perpendicular orientation of cylindrical domains upon solvent annealing thin films of polystyrene-b-polylactide , 2010 .

[27]  Linus Pauling,et al.  The Nature of the Chemical Bond and the Structure of Molecules and Crystals , 1941, Nature.

[28]  Timothy W. Collins,et al.  Brushless and controlled microphase separation of lamellar polystyrene‐b‐polyethylene oxide thin films for block copolymer nanolithography , 2012 .

[29]  Hiroshi Gokan,et al.  Dry Etch Resistance of Organic Materials , 1983 .

[30]  Justin D. Holmes,et al.  Plasma etch technologies for the development of ultra-small feature size transistor devices , 2011 .

[31]  M. Hillmyer,et al.  Ordered nanoporous polymers from polystyrene-polylactide block copolymers. , 2002, Journal of the American Chemical Society.

[32]  G. Fredrickson,et al.  Defectivity in Laterally Confined Lamella-Forming Diblock Copolymers: Thermodynamic and Kinetic Aspects , 2012 .

[33]  Justin D. Holmes,et al.  Monitoring PMMA Elimination by Reactive Ion Etching from a Lamellar PS-b-PMMA Thin Film by ex Situ TEM Methods , 2010 .

[34]  Zhiqun Lin,et al.  Controlled evaporative self-assembly of hierarchically structured bottlebrush block copolymer with nanochannels , 2011 .

[35]  H. Yabu,et al.  Reorientation of Microphase-Separated Structures in Water-Suspended Block Copolymer Nanoparticles through Microwave Annealing , 2013 .

[36]  A. Whittaker,et al.  Control of the orientation of symmetric poly(styrene)-block-poly(D,L-lactide) block copolymers using statistical copolymers of dissimilar composition. , 2012, Langmuir : the ACS journal of surfaces and colloids.

[37]  H. Sung,et al.  Pore-filling nanoporous templates from degradable block copolymers for nanoscale drug delivery. , 2009, ACS nano.

[38]  C. Simão,et al.  Defect analysis and alignment quantification of line arrays prepared by directed self-assembly of a block copolymer , 2014, Advanced Lithography.

[39]  M. Morris,et al.  Selective etching of polylactic acid in poly(styrene)‐block‐poly(d,l)lactide diblock copolymer for nanoscale patterning , 2014 .

[40]  Shouwu Guo,et al.  Nanopore and nanobushing arrays from ABC triblock thin films containing two etchable blocks , 2006 .

[41]  T. Lodge,et al.  Mechanisms of chain diffusion in lamellar block copolymers. , 1995, Physical review letters.

[42]  M. Morris,et al.  Sub-10 nm feature size PS-b-PDMS block copolymer structures fabricated by a microwave-assisted solvothermal process. , 2013, ACS applied materials & interfaces.

[43]  Hideaki Yokoyama,et al.  Diffusion of block copolymers , 2006 .

[44]  A. Jonas,et al.  Staining of poly(ethylene terephthalate) by ruthenium tetroxide , 2003 .