Recombination in quantum dot sensitized solar cells.
Quantum dot sensitized solar cells (QDSCs) have attracted significant attention as promising third-generation photovoltaic devices. In the form of quantum dots (QDs), the semiconductor sensitizers have very useful and often tunable properties; moreover, their theoretical thermodynamic efficiency might be as high as 44%, better than the original 31% calculated ceiling. Unfortunately, the practical performance of these devices still lags behind that of dye-sensitized solar cells. In this Account, we summarize the strategies for depositing CdSe quantum dots on nanostructured mesoporous TiO(2) electrodes and discuss the methods that facilitate improvement in the performance and stability of QDSCs. One particularly significant factor for solar cells that use polysulfide electrolyte as the redox couple, which provides the best performance among QDSCs, is the passivation of the photoanode surface with a ZnS coating, which leads to a dramatic increase of photocurrents and efficiencies. However, these solar cells usually show a poor current-potential characteristic, so a general investigation of the recombination mechanisms is required for improvements. A physical model based on recombination through a monoenergetic TiO(2) surface state that takes into account the effect of the surface coverage has been developed to better understand the recombination mechanisms of QDSCs. The three main methods of QD adsorption on TiO(2) are (i) in situ growth of QDs by chemical bath deposition (CBD), (ii) deposition of presynthesized colloidal QDs by direct adsorption (DA), and (iii) deposition of presynthesized colloidal QDs by linker-assisted adsorption (LA). A systematic investigation by impedance spectroscopy of QDSCs prepared by these methods showed a decrease in the charge-transfer resistance and increased electron lifetimes for CBD samples; the same result was found after ZnS coating because of the covering of the TiO(2) surface. The increase of the lifetime with the ZnS treatment has also been checked independently by open-circuit potential (V(oc)) decay measurements. Despite the lower recombination rates by electron transfer to electrolyte as well as the higher light absorption of CBD samples, only a moderate increase of photocurrent compared with colloidal QD samples is obtained, indicating the presence of an additional, internal recombination pathway in the closely packed QD layer.
Controlling the influence of Auger recombination on the performance of quantum-dot light-emitting diodes
Development of light-emitting diodes (LEDs) based on colloidal quantum dots is driven by attractive properties of these fluorophores such as spectrally narrow, tunable emission and facile processibility via solution-based methods. A current obstacle towards improved LED performance is an incomplete understanding of the roles of extrinsic factors, such as non-radiative recombination at surface defects, versus intrinsic processes, such as multicarrier Auger recombination or electron-hole separation due to applied electric field. Here we address this problem with studies that correlate the excited state dynamics of structurally engineered quantum dots with their emissive performance within LEDs. We find that because of significant charging of quantum dots with extra electrons, Auger recombination greatly impacts both LED efficiency and the onset of efficiency roll-off at high currents. Further, we demonstrate two specific approaches for mitigating this problem using heterostructured quantum dots, either by suppressing Auger decay through the introduction of an intermediate alloyed layer, or by using an additional shell that impedes electron transfer into the quantum dot to help balance electron and hole injection.
genetic algorithm positioning system process control sample size solar cell visible light dna sequence learning object indoor positioning received signal strength statistical process control indoor localization quantum dot statistical proces indoor positioning system count datum hecke algebra factorial design ieee standard binding site escherichia coli weighted moving average knowledge structure statistical quality control poisson structure cell cycle choice behavior econometric model quality level exponentially weighted moving fractional factorial design saccharomyces cerevisiae selection bia affine weyl group statistical process monitoring power conversion efficiency dye-sensitized solar cell charge transport uniform resource identifier learning object metadatum embryonic stem cell moving average control object class dye-sensitized solar reusable learning object linkage disequilibrium quantity discount spatial process spatial econometric population parameter embryonic stem reusable learning object metadatum heterojunction solar cell dna repair location fingerprinting cell development indoor positioning technique spatial econometric model radiation tolerance heterojunction solar genetic linkage signal peptide bulk heterojunction dna segment recombination rate bulk heterojunction solar dna recombination wifi-based indoor localization surface recombination escherichia coli. low-density lipoprotein indoor positioning solution proposed positioning system surface recombination velocity solar cells. neisseria meningitidi genetic heterogeneity learning object review dna break xrcc5 wt allele xrcc5 gene t cell receptor v(d)j recombination v(d)j recombination-activating protein 1 excretory function neuritis, autoimmune, experimental leukemia, b-cell dna sequence rearrangement immunoglobulin class switch recombination immunoglobulin class switching lipoprotein receptor dna breaks, double-stranded telomere maintenance v(d)j recombination genome encoded entity vdj recombinase recombination, genetic crossover (genetic algorithm) meiotic recombination homologous recombination