Deadbeat Direct Torque and Flux Control of IPMSM Drives Using a Minimum Time Ramp Trajectory Method at Voltage and Current Limits

This paper presents the voltage- and current-limited operation of an interior permanent magnet synchronous machine (IPMSM) using deadbeat direct torque and flux control (DB-DTFC). A commanded air-gap torque and stator flux can be achieved by the end of each pulsewidth modulation (PWM) period using DB-DTFC. However, it may take several PWM periods to achieve a desired air-gap torque that is physically infeasible in one step due to voltage limits. In that case, the torque and flux command trajectories operating over multiple periods can be developed to achieve deadbeat torque and flux response for every PWM period. The torque and flux command trajectories can be developed in different shapes depending on desired objectives. In this paper, a minimum-time ramp trajectory method is proposed to achieve both simple real-time implementation and fast and stable transient dynamics of IPMSM drives. Simulation and experimental results for the minimum-time ramp trajectory method for an IPMSM drive are presented.

[1]  Shinji Doki,et al.  Fast Torque Control System of PMSM based on Model Predictive Control Considering Overmodulation Region , 2010 .

[2]  Graham C. Goodwin,et al.  Adaptive filtering prediction and control , 1984 .

[3]  Tae-Suk Kwon,et al.  Novel anti-windup of a current regulator of a surface-mounted permanent-magnet motor for flux-weakening control , 2005 .

[4]  Joachim Holtz,et al.  On continuous control of PWM inverters in the overmodulation range including the six-step mode , 1993 .

[5]  Robert D. Lorenz,et al.  One-step optimal space vector PWM current regulation using a neural network , 1994, Proceedings of 1994 IEEE Industry Applications Society Annual Meeting.

[6]  A very fast direct torque control for interior permanent magnet synchronous motors start up , 2005 .

[7]  H. Abu-Rub,et al.  Sensorless Control of Induction Motors for Maximum Steady-State Torque and Fast Dynamics at Field Weakening , 2006, Conference Record of the 2006 IEEE Industry Applications Conference Forty-First IAS Annual Meeting.

[8]  Seung-Ki Sul,et al.  Generalized solution of minimum time current control in three-phase balanced systems , 1998, IEEE Trans. Ind. Electron..

[9]  K. D. Tocher,et al.  Sampled‐Data Control Systems , 1959 .

[10]  Thomas G. Habetler,et al.  Performance evaluation of a direct torque controlled drive in the continuous PWM-square wave transition region , 1993 .

[11]  R. Lorenz,et al.  Flux-Based Deadbeat Control of Induction-Motor Torque , 2003 .

[12]  Kwanghee Nam,et al.  A dynamic decoupling control scheme for high-speed operation of induction motors , 1999, IEEE Trans. Ind. Electron..

[13]  Robert D. Lorenz,et al.  Time optimal torque control and loss minimization in AC machines using deadbeat direct torque and flux control , 2011, 2011 International Conference on Electrical Machines and Systems.

[14]  Shengming Li,et al.  Torque control patching and anti-windup and bumpless transfer conditioning of current regulators for high-speed PMSM systems , 2001, 2001 IEEE 32nd Annual Power Electronics Specialists Conference (IEEE Cat. No.01CH37230).

[15]  Robert D. Lorenz,et al.  Time-Optimal and Loss-Minimizing Deadbeat-Direct Torque and Flux Control for Interior Permanent-Magnet Synchronous Machines , 2014 .

[16]  Robert D. Lorenz,et al.  Robustness analysis of deadbeat-direct toque and flux control for IPMSM drives , 2013, 2013 15th European Conference on Power Electronics and Applications (EPE).

[17]  Chan-Hee Choi,et al.  Wide-Speed Direct Torque and Flux Control for Interior PM Synchronous Motors Operating at Voltage and Current Limits , 2013, IEEE Transactions on Industry Applications.

[18]  Robert D. Lorenz,et al.  Deadbeat-Direct Torque and Flux Control of Interior Permanent Magnet Synchronous Machines With Discrete Time Stator Current and Stator Flux Linkage Observer , 2011, IEEE Transactions on Industry Applications.

[19]  Robert D. Lorenz,et al.  Robustness Analysis of Deadbeat-Direct Torque and Flux Control for IPMSM Drives , 2016, IEEE Transactions on Industrial Electronics.

[20]  D. Casadei,et al.  A Comparison of Four Robust Control Schemes for Field-Weakening Operation of Induction Motors , 2012, IEEE Transactions on Power Electronics.

[21]  Myung-Joong Youn,et al.  A dead-beat type digital controller for the direct torque control of an induction motor , 2002 .

[22]  R. Bellman.  Dynamic programming. , 1957, Science.

[23]  Shengming Li,et al.  A fast response torque control for interior permanent-magnet synchronous motors in extended flux-weakening operation regime , 2001, IEMDC 2001. IEEE International Electric Machines and Drives Conference (Cat. No.01EX485).

[24]  S. Doki,et al.  Novel Techniques for Fast Torque Response of IPMSM Based on Space-Vector Control Method in Voltage Saturation Region , 2007, IECON 2007 - 33rd Annual Conference of the IEEE Industrial Electronics Society.

[25]  Robert D. Lorenz,et al.  Robustness evaluation of deadbeat, direct torque and flux control for induction machine drives , 2009, 2009 13th European Conference on Power Electronics and Applications.

[26]  R. Arthur Bergen,et al.  Sampled-data processing techniques for feedback control systems , 1954, Transactions of the American Institute of Electrical Engineers, Part II: Applications and Industry.

[27]  R.D. Lorenz,et al.  Digital Implementation of Stator and Rotor Flux-Linkage Observers and a Stator-Current Observer for Deadbeat Direct Torque Control of Induction Machines , 2009, IEEE Transactions on Industry Applications.

[28]  M. Depenbrock,et al.  Direct self control of inverter-fed induction machine, a basis for speed control without speed-measurement , 1989, Conference Record of the IEEE Industry Applications Society Annual Meeting,.

[29]  Sean R Eddy,et al.  What is dynamic programming? , 2004, Nature Biotechnology.

[30]  Shinji Doki,et al.  Fast torque control system of PMSM based on model predictive control , 2009, 2009 35th Annual Conference of IEEE Industrial Electronics.

[31]  Shinji Doki,et al.  Voltage limiter calculation method for fast torque response of IPMSM in overmodulation range , 2009, 2009 35th Annual Conference of IEEE Industrial Electronics.