Integrated control of solidification microstructure and melt pool dimensions in electron beam wire feed additive manufacturing of Ti-6Al-4V

Abstract The ability to deposit a consistent and predictable solidification microstructure can greatly accelerate additive manufacturing (AM) process qualification. Process mapping is an approach that represents process outcomes in terms of process variables. In this work, a solidification microstructure process map was developed using finite element analysis for deposition of single beads of Ti-6Al-4V via electron beam wire feed AM processes. Process variable combinations yielding constant beta grain size and morphology were identified. Comparison with a previously developed process map for melt pool geometry shows that maintaining a constant melt pool cross sectional area will also yield a constant grain size. Additionally, the grain morphology boundaries are similar to curves of constant melt pool aspect ratio. Experimental results support the numerical predictions and identify a proportional size scaling between beta grain widths and melt pool widths. Results further demonstrate that in situ indirect control of solidification microstructure is possible through direct melt pool dimension control.

[1]  B. Baufeld,et al.  Additive manufacturing of Ti–6Al–4V components by shaped metal deposition: Microstructure and mechanical properties , 2010 .

[2]  Ryan B. Wicker,et al.  Effect of Melt Scan Rate on Microstructure and Macrostructure for Electron Beam Melting of Ti-6Al-4V , 2012 .

[3]  Jack Beuth,et al.  Process Maps for Predicting Residual Stress and Melt Pool Size in the Laser-Based Fabrication of Thin-Walled Structures , 2007 .

[4]  M. Donachie.  Titanium: A Technical Guide , 1988 .

[5]  J. Hunt,et al.  Steady state columnar and equiaxed growth of dendrites and eutectic , 1984 .

[6]  S. L. Semiatin,et al.  The effect of laser power and traverse speed on microstructure, porosity, and build height in laser-deposited Ti-6Al-4V , 2000 .

[7]  H. Fraser,et al.  Thermal process maps for predicting solidification microstructure in laser fabrication of thin-wall structures , 2006 .

[8]  Karen M. Taminger,et al.  Electron Beam Freeform Fabrication (EBF3) for Cost Effective Near-Net Shape Manufacturing , 2006 .

[9]  P. Prangnell,et al.  Effect of Wall Thickness Transitions on Texture and Grain Structure in Additive Layer Manufacture (ALM) of Ti-6Al-4V , 2012 .

[10]  Ryan B. Wicker,et al.  Microstructures and mechanical properties of electron beam-rapid manufactured Ti–6Al–4V biomedical prototypes compared to wrought Ti–6Al–4V , 2009 .

[11]  N. Klingbeil,et al.  Thermal Process Maps for Controlling Microstructure in Laser-Based Solid Freeform Fabrication , 2003 .

[12]  Christoph Leyens,et al.  Mechanical Properties of Additive Manufactured Ti-6Al-4V Using Wire and Powder Based Processes , 2011 .

[13]  Timothy P. Quinn,et al.  Effects of processing on microstructure and mechanical properties of a titanium alloy (Ti–6Al–4V) fabricated using electron beam melting (EBM), Part 2: Energy input, orientation, and location , 2013 .

[14]  J. Beuth,et al.  Process Mapping of Transient Melt Pool Response in Wire Feed E-Beam Additive Manufacturing of Ti-6Al-4V , 2013 .

[15]  Jack L. Beuth,et al.  CONTROLLING MELT POOL DIMENSIONS OVER A WIDE RANGE OF MATERIAL DEPOSITION RATES IN ELECTRON BEAM ADDITIVE MANUFACTURING , 2010 .

[16]  S. L. Semiatin,et al.  Microstructure and texture evolution during solidification processing of Ti–6Al–4V , 2003 .

[17]  J. Beuth,et al.  The role of process variables in laser-based direct metal solid freeform fabrication , 2001 .

[18]  Jack Beuth,et al.  Process Mapping for Qualification Across Multiple Direct Metal Additive Manufacturing Processes , 2013 .

[19]  Jack Beuth,et al.  Understanding Ti-6 Al-4 V Microstructure Control in Additive Manufacturing via Process Maps , 2013 .

[20]  Francis H. Froes,et al.  Producing titanium aerospace components from powder using laser forming , 2000 .

[21]  Standard Test Methods for Determining Average Grain Size 1 , 2006 .

[22]  Timothy P. Quinn,et al.  Effects of processing on microstructure and mechanical properties of a titanium alloy (Ti–6Al–4V) fabricated using electron beam melting (EBM), part 1: Distance from build plate and part size , 2013 .

[23]  Christoph Leyens,et al.  Morphology, microstructure, and hardness of titanium (Ti-6Al-4V) blocks deposited by wire-feed additive layer manufacturing (ALM) , 2012 .

[24]  H. Fraser,et al.  Effects of process variables and size-scale on solidification microstructure in beam-based fabrication of bulky 3D structures , 2009 .