Design and motion analysis of load-carrying and transmit robot (LCT-Robot) for small openings

This paper proposes a Load-carrying and transmit robot (LCT-Robot), which is based on a novel modular joint, for the purpose of telemaintenance of the Tokamak First wall (FW). The LCT-Robot, which is installed on a Multipurpose transport cask (MTC) and plays the role of transmitting and load-carrying, has the adaptability to several of maintenance tasks by carrying different types of micro-robots. The transmission mechanism of LCT-Robot modular joint and structural “lightweight” design is comprehensively considered through establishing the geometric parameter constraint equations related to Tokamak FW. It can steadily provide the ability of long-distance transmitting and performs maintenance tasks when the weight of the micro-robot is changed. Without any gravity compensation, the LCT-robot equipped with ordinary drive motor can bear a wide range of load. It not only satisfies the higher load, but also enhances the efficiency of the drive motor. For avoiding frequent acceleration and deceleration of the LCT-robot, the entire process through small openings from the placement state (0-state) to the flattened state (3-state) is analyzed and the effective translational distance of MTC is confirmed. As a result, experiment verifies the effectiveness of the LCT-robot, which has a length of 2.95 meters and can smoothly pass through small openings (Width: 200 mm, Height: 250 mm).

[1]  Guiying Li,et al.  Conceptual design of EAST flexible in-vessel inspection system , 2010 .

[2]  Marek J. Rubel,et al.  Current status of the JET ITER-like Wall Project , 2009 .

[3]  Thomas A. Fuhlbrigge,et al.  Automated industrial robot path planning for spray painting process: A review , 2008, 2008 IEEE International Conference on Automation Science and Engineering.

[4]  Howie Choset,et al.  Design of a modular snake robot , 2007, 2007 IEEE/RSJ International Conference on Intelligent Robots and Systems.

[5]  Blake Hannaford,et al.  Evaluation of liver tissue damage and grasp stability using finite element analysis , 2016, Computer methods in biomechanics and biomedical engineering.

[6]  Mukesh Didwania,et al.  Modal analysis of drive shaft using FEA , 2013 .

[7]  J. P. Friconneau,et al.  Real time command control architecture for an ITER relevant inspection robot in operation on Tore Supra , 2009 .

[8]  Howie Choset,et al.  Design and architecture of the unified modular snake robot , 2012, 2012 IEEE International Conference on Robotics and Automation.

[9]  Jerry M. Mendel,et al.  Design of Novel Interval Type-2 Fuzzy Controllers for Modular and Reconfigurable Robots: Theory and Experiments , 2011, IEEE Transactions on Industrial Electronics.

[10]  Qiang Zhang,et al.  Development and Analysis of a Long Reach Robot for EAST Vacuum Vessel Inspection , 2015 .

[11]  K. P. Padmanaban,et al.  Recent developments on machining fixture layout design, analysis, and optimization using finite element method and evolutionary techniques , 2013, The International Journal of Advanced Manufacturing Technology.

[12]  K-D Zastrow,et al.  Implementation of an in-vessel calibration light source for JET. , 2012, The Review of scientific instruments.

[13]  Elaheh Hassanzadeh Toreh,et al.  Kinematic and Kinetic Study of Rescue Robot by SolidWorks Software , 2013 .

[14]  Satoshi Murata,et al.  Toward a scalable modular robotic system , 2007, IEEE Robotics & Automation Magazine.

[15]  Y. Perrot,et al.  ITER Articulated Inspection Arm (AIA): Geometric calibration issues of a long-reach flexible robot , 2005 .

[16]  Gregory Dubus,et al.  Vibration control of an IVVS long-reach deployer using unknown visual features from inside the ITER vessel , 2010 .

[17]  W. P. Hew,et al.  Design, Analysis, and Prototyping of an Axial-Flux Permanent Magnet Motor Based on Genetic Algorithm and Finite-Element Analysis , 2013, IEEE Transactions on Magnetics.

[18]  Torgny Brogårdh,et al.  Present and future robot control development - An industrial perspective , 2007, Annu. Rev. Control..

[19]  M. N. A. Beurskens,et al.  JET ITER-like wall—overview and experimental programme , 2011 .

[20]  Guangjun Liu,et al.  Power efficiency estimation based health monitoring and fault detection of modular and reconfigurable robot , 2008, 2008 IEEE International Conference on Automation and Logistics.

[21]  Jianjun Yuan,et al.  Active cooling system for Tokamak in-vessel operation manipulator , 2015 .

[22]  Yuntao Song,et al.  Concept design on RH maintenance of CFETR Tokamak reactor , 2014 .

[23]  John Norrish,et al.  Recent Progress on Programming Methods for Industrial Robots , 2010, ISR/ROBOTIK.

[24]  Micaël Michelin,et al.  Fusion reactor handling operations with cable-driven parallel robots , 2015 .

[25]  Nikolaos G. Tsagarakis,et al.  A variable physical damping actuator (VPDA) for compliant robotic joints , 2010, 2010 IEEE International Conference on Robotics and Automation.