A novel modular compliant knee joint actuator for use in assistive and rehabilitation orthoses

Despite significant advancements in the field of wearable robots (WRs), commercial WRs still use traditional direct-drive actuation units to power their joints. On the other hand, in research prototypes compliant actuators are increasingly being used to more adequately address the issues of safety, robustness, control and overall system efficiency. The advantages of mechanical compliance are exploited in a novel modular actuator prototype designed for the knee joint. Due to its modularity, the actuator can be implemented in a knee joint of a standalone or a multi-joint lower-limbs orthosis, for use in gait rehabilitation and/or walking assistance. Differently from any other actuator used in orthotic research prototypes, it combines a Variable Stiffness Actuator (VSA) and a Parallel Elasticity Actuation (PEA) unit in a single modular system. Although independent, the units are designed to work together in order to fully mimic dynamic behavior of the human knee joint. In this paper, design aspects and functional evaluation of the new actuator are presented and a rationale for such a design in biomechanics of the human knee joint is given. The VSA subsystem is characterized in a quasi-static benchmarking environment and the results showing main performance indicators are presented.

[1]  Aaron M. Dollar,et al.  Design and Functional Evaluation of a Quasi-Passive Compliant Stance Control Knee–Ankle–Foot Orthosis , 2014, IEEE Transactions on Neural Systems and Rehabilitation Engineering.

[2]  Bram Vanderborght,et al.  Mechanical design of a lightweight compliant and adaptable active ankle foot orthosis , 2016, 2016 6th IEEE International Conference on Biomedical Robotics and Biomechatronics (BioRob).

[3]  Reinhard Blickhan,et al.  Compliant leg behaviour explains basic dynamics of walking and running , 2006, Proceedings of the Royal Society B: Biological Sciences.

[4]  Hugh M. Herr,et al.  Clutchable series-elastic actuator: Implications for prosthetic knee design , 2014, Int. J. Robotics Res..

[5]  Aaron M. Dollar,et al.  On the mechanics of the knee during the stance phase of the gait , 2011, 2011 IEEE International Conference on Rehabilitation Robotics.

[6]  Aaron M. Dollar,et al.  Design of a quasi-passive knee exoskeleton to assist running , 2008, 2008 IEEE/RSJ International Conference on Intelligent Robots and Systems.

[7]  Grant Elliott,et al.  Design of a Clutch–Spring Knee Exoskeleton for Running , 2014 .

[8]  Bram Vanderborght,et al.  Design of Smart Modular Variable Stiffness Actuators for Robotic-Assistive Devices , 2017, IEEE/ASME Transactions on Mechatronics.

[9]  A. Amis,et al.  i) Biomechanics of the knee joint , 2010 .

[10]  Nikolaos G. Tsagarakis,et al.  iT-Knee: An exoskeleton with ideal torque transmission interface for ergonomic power augmentation , 2016, 2016 IEEE/RSJ International Conference on Intelligent Robots and Systems (IROS).

[11]  André Seyfarth,et al.  A comparison of parallel- and series elastic elements in an actuator for mimicking human ankle joint in walking and running , 2012, 2012 IEEE International Conference on Robotics and Automation.

[12]  Nikolaos G. Tsagarakis,et al.  AwAS-II: A new Actuator with Adjustable Stiffness based on the novel principle of adaptable pivot point and variable lever ratio , 2011, 2011 IEEE International Conference on Robotics and Automation.

[13]  J Geeroms,et al.  Design and energetic evaluation of a prosthetic knee joint actuator with a lockable parallel spring , 2017, Bioinspiration & biomimetics.

[14]  Richard A. Brand,et al.  The biomechanics and motor control of human gait: Normal, elderly, and pathological , 1992 .

[15]  Aaron M. Dollar,et al.  Effects of exoskeletal stiffness in parallel with the knee on the motion of the human body center of mass during walking , 2015, 2015 IEEE International Conference on Robotics and Automation (ICRA).

[16]  Juan Carlos Arevalo,et al.  An Adjustable Compliant Joint for Lower-Limb Exoskeletons , 2015, IEEE/ASME Transactions on Mechatronics.

[17]  Hugh Herr,et al.  Agonist-antagonist active knee prosthesis: a preliminary study in level-ground walking. , 2009, Journal of rehabilitation research and development.

[18]  Joost Geeroms,et al.  Mechatronic design of a sit-to-stance exoskeleton , 2014, 5th IEEE RAS/EMBS International Conference on Biomedical Robotics and Biomechatronics.

[19]  Bram Vanderborght,et al.  Conceptual design of a novel variable stiffness actuator for use in lower limb exoskeletons , 2015, 2015 IEEE International Conference on Rehabilitation Robotics (ICORR).

[20]  Nikolaos G. Tsagarakis,et al.  A new variable stiffness actuator (CompAct-VSA): Design and modelling , 2011, 2011 IEEE/RSJ International Conference on Intelligent Robots and Systems.

[21]  Herman van der Kooij,et al.  Modeling, design, and optimization of Mindwalker series elastic joint , 2013, 2013 IEEE 13th International Conference on Rehabilitation Robotics (ICORR).

[22]  Joost Geeroms,et al.  Design of a modular add-on compliant actuator to convert an orthosis into an assistive exoskeleton , 2014, 5th IEEE RAS/EMBS International Conference on Biomedical Robotics and Biomechatronics.

[23]  Elliott J. Rouse,et al.  Design and Validation of a Torque-Controllable Knee Exoskeleton for Sit-to-Stand Assistance , 2017, IEEE/ASME Transactions on Mechatronics.

[24]  H. van der Kooij,et al.  Design of a series elastic- and Bowden cable-based actuation system for use as torque-actuator in exoskeleton-type training , 2005, 9th International Conference on Rehabilitation Robotics, 2005. ICORR 2005..